Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
HI NORDIC TEAM
Hello!
Does the NORDIC chip support the BLUETOOTH 3D Synchronization Profile?
Are there any relevant documents or procedures that can be referred to?...
Hello,
our project which started 7 years ago with SDK13.0 has been migrated some time ago to SDK 15.3 and now to SDK17.1. At the beginning we were quite happy with the RTT...
Dear Nordic Engineers
I developed a PWM function to drive the RGB LED. Then I found a problem, which is w hen I used a PWM signal of one channel to control the RED light...
Hi,
I'm developing my app on nRF52840, NCS2.7.0 on VS Code 1.100.0.
My application needs to save settings data (4 x int32_t ) to external the NOR Flash (mx25r64) in `settings_storage...
Hello,
nRF Connect SDK v3.0.1 nRF54L15-DK v0.9.1
Currently, I’m exploring whether it’s possible to create a Bluetooth application that can be controlled from an external...
Hi,
I am using nrf54l15 ,here I have bare i2s code for reading data from mics and ble code for notifying that data but here I am planning to use lc3 codec to compress data...
I have just purchased nRF54L15 DK, run Quick Start and programmed 'Hello World', but the verification failed and nothing happened. I opened the serial terminal, but nothing...
I'm following the tutorial Exercise 1 – Custom board for single-core SoC using ncs v2.9.0 with one slight difference in that I'm using a nRF52DK with nRF52832 because that...
Hello,
I am running firmware on a custom board toting an nrf5340 with NCS version 2.3.0. There is also a Micron 8Gb NAND flash on board that I have a custom driver for....
Hello,
I'm currently working with the channel_sounding_ras_initiator project on the nRF54L15 DK , using the nRF Connect SDK from the latest main branch on GitHub ( nrfconnect...
Hello~ I used the ot-nrf528xx codebase for compilation, and according to the content in the readme, I compiled two Hex files for USB and SPI interfaces using the USB_trans...
Hi, the nordic team
I am working on thread protocol using SDK version 2.9.1.
I use the SED device,My poll is 1000 ms. How can I receive messages from my parent node when...
Hi,
I am power profiling an application on the NRF52 DK. The application uses SPI to communicate with the BMA400 accelerometer:
The program initializes the accelerometer...
Dear support team,
I am getting an error while performing DFU using nRF Connect.
My SDK version is 2.4.2, I need to do DFU using BLE simultaneously, for that i tried...
