Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
Segger RTT (Real-Time Terminal) supports multiple data channels.
RTT Viewer uses channel 0 only, and implements multiple virtual terminals on top of this. The terminal...
I use nrf52832 + SoftDevices132_nrf52_3.1.0.
sd_ble_gap_scan_start() run with scan_interval=scan_window=5ms.
I look at scan-channel-switch time is about 1ms. (I analyze...
i want add in project adc. i changed my sdk_config.h and Makefile .
i incuded in main file
#include "nrf_drv_pwm.h"
#include "nrf_drv_adc.h"
i have error ghjgjghj...
I use a Peer Manager in my project (nrf52832, SDK13.1).
Peer manager use FDS, but i also want to use FDS for storing user data.
As i know , FDS module use 1 virtural page...
Hi all,
I have here NRF51-DK, I am a bit familiar with the kit for a while.
Now I want to make a system using NRF518422 chip.
I manage to find a module - "Taiyo Yuden EYAGJNZXX...
I'm starting to read all the resources and examples included in the SDK. However, there doesn't seem to be a lot of emphasis on explaining how the programming architecture...
Hello,
I have the following observation regarding the potential problem with DFU bootloader
implementation :
I have noticed that the Bootloader DFU implementation (nRF5_SDK_13...
Hello!
I would like to program the nRF52 using the JLink Commander and protect it afterwards. Which register do I need to manipulate?
Thanks and kind regards,
Mi...
I download the nRF Toolbox app and its in swift.
My current app is in objective-C and I want to implement dfu in my app.
Is there any framework that can be used in my...
Hello,
I recently migrated to nrf52 and countering some problems
with NRF_ESB concurrently with BLE.
I started with This example which was a part of the Running micro...
The chip is nrf52832.
The SDK version that I am using is nRF5_SDK_13.1.0_7ca7556,the example that i used is ble_app_uart.
When i debug about low power,i encounter problems...
Hello,
I'm using NRF51-DK (PCA10028) and I want to be sure if I'm using the external 32KHz oscillator (X2).
I'm using SDK12.3.0. I'm running the beacon example.
In...
Hi,
Is there any tutorial already for the version 14.0.0 of the SDK (nRF52, more specifically I am using nRF52832)? I would like to know how to configure Advertising, and...
Hi
I have development kit nrf51 PCA 10028 and try to run uart example example with loopback (RX connected to TX, RTS connected to CTS). Unfortunately, after sending, I...
I'm using the bootloader_secure_ble example from SDK 13 on an nRF52832. I'm using the GCC toolchain. Here is an extract of the linker file from the example:
MEMORY
{
...
