But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi,
I need you suggestion / information about Nordic chip. We currently have nRF52 (nRF52832) chip. However, in our application we will be using Nordic beacons as an transmitter...
Hello All,
I've finally managed to get Eclipse up and running after migrating from Keil, but now I'm having the following problem: I'm trying to port the buttonless_dfu...
Hi,
Happy Monday! We have multiple PTXs and multiple PRXs in a setting, all operating on a single channel. Is there a way to allow a PRX to receive but disable it from...
Hello,
We have observed fluctuation in Gas sensor readings from Nordic Thingy:52.
eCo2 and VOC readings are not at all near the calibrated sensor readings.
Tried Nordic...
Hello,
I am in a little bit of trouble here trying to flash a 3rd party module that is mounted on a custom PCB I made with the SWD pins exposed for programming.
I've...
Hello,
I am using pca10040 and sdk12.2. I am using nrf_beacon code. I flashed the code in dk. I am able to scan the beacon but I n/a appears as default name in nrf connect...
Hi team,
My 52832 act as central device. It can discover service and characteristic of peripheral. The problem is it can't get the UUID of every characteristic of service...
Hello! I try to add nus service to ble_app_template.
I add ble_nus.c file into project
add include "ble_nus.h"
declared service
BLE_NUS_DEF(m_nus);
add into...
I guess my question is stupid, but I would like to ask it by the way..
in all ble examples we use a function for handling ble events by our app
in my case in example ble_app_uart...
I'm trying to launch my app on a custom board with nrf52 after a successful launching on DK. The problem is here: err_code = sd_softdevice_enable(p_clock_lf_cfg, softdevice_fault_handler...
Hi folks, I'm making progress with a program to get two nRF24L01p modules communicating with each other, but there are a couple of remaining problems. I hope someone can help...
I have a little bit of experience on TI BLE stack development and wanted to move to Nordic product with Bluetooth or ANT protocol for a higher data rate. I got a general question...
Hi All,
I have a problem with .hex file. I use example ble_app_uart from nRF5_SDK.
In examples\ble_peripheral\ble_app_uart\pca10056\s140\armgcc I executed: make all and...
I try to turn off the system with sd_power_system_off()
// Go to system-off mode (this function will not return; wakeup will cause a reset).
err_code = sd_power_system_off...
