This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi,
I'm trying to run the gdb on the nRF52 with softdevice s132 and in the begining it runs ok but after some time when I run (gdb) list I get: "Line number 435 out of...
Hello,
I'd like to send 16 bits data over ble instead of 8 bits
gatts_value.offset = 0;
gatts_value.len = len;
gatts_value.p_value = data;
err_code = sd_ble_gatts_value_set...
The call to ble_x_handles_assign() is not uniformized on all the examples. It's sometime call from on_ble_evt() or/and from x_evt_handler() .
From the doc on the function...
What shoul i do? 0 erro with code
SEGGER J-Link GDB Server V6.20d Command Line Version
1. JLinkARM.dll V6.20d (DLL compiled
Sep 29 2017 16:44:59)
Command...
I am using S120 Softdevice, with bunch of different type ble tags(peripherals). written a code to connect multiple tags at a time and doing a gattc read to fetch the battery...
I have a technical issue I am facing while doing development with Nordic NRF52840. I have an application which I am sending command though virtual com port using CDC ACM USB...
Hello everyone!
I am learning with nrf52840 MCU and SDK version 13. When I read the example. I see one line:
SVCALL(SD_BLE_GAP_CONNECT, uint32_t, sd_ble_gap_connect(ble_gap_addr_t...
Hi,
I'm developing a project based on nRF52 and utilizing NFC for my master's degree. One part of the project will be a beacon with as small PCB layout as possible. That...
Hi,
Often when I try connect BLED112 dongle to bluetooth module BMD-300 by command:
ble_cmd_gap_connect_direct(DeviceMAC, gap_address_type_random, 60, 76, 100, 0); ...
hi,
i want to add uart function to my application. so i added necessary .c files to my project. if i compile the program i am getting these errors.
when i change the...
Hi,
I have Raspberry PI 3 Model B Rev 1.2 running "Linux raspberrypi 4.9.41-v7+ #1023 SMP Tue Aug 8 16:00:15 BST 2017 armv7l GNU/Linux". Running BlueZ 5.43
I can connect...
Hi community,
Try use FDS to write some data before sleep.
Following example and test is work.
But I try write data before into
sd_power_system_off();
...
Firstly the develop environment.
Windows 10
KEIL as IDE
Device: nrf 51822 - sd s130 2.0.1 - SDK 12.1 nRF5_SDK_12.0.0_12f24da.zip
Use case:
We have 2 application mode...
Hello i am using segger studio i have recently purchased three nrf52dk speically for ble mesh..
i am trying to run examples of mesh alpha sdk that nordiac prvodies but it...
