I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hi, Wizzards
I understand that the QSPI is made solely for external flash, but we are in a hurry to make a driver for a RGB LED module with a common clock. It would be good...
I have been using nRF Toolbox –DFU to reflash my project. I am using an Android tablet version 6.0.1. This process was working very nicely.
On 2/5/2020 the tablet updated...
Hi,
I have a really hard time with nRF connect. I wrote a simple app for my Dongle and when I want to program it via nRF connect it says that Device not found due to failure...
Hi,
We're trying to add a custom service to the HID keyboard example. the service is initialized we can see the service when connected to the device from the nrfConnect...
I tried original ble_app_hids_keyboard_pca10040_s112 example, then modify it by moving the code for typing h.e.l.l.o from Btn 1 to Btn3, and all possible combination of sd_ble_gap_disconnect...
I've tried using LESC without bonding, but iOS displays a pairing dialog. I don't think it is possible to avoid this, so the only way to avoid the pairing dialog is to use...
We are using nRF52832 to develop our product with the ANCS function.
But after bonding with the iPhone and then restart the iPhone, an error message "NRF_ERROR_BUSY" will...
Hi,
I've setup nRF Connect SDK v1.1.0 and I was taking a look at the the peipheral_uart example. I couldn't find any API reference when I searched in the v1.1.0 documentation...
Hello,
I sae that there is the possibility to upgrade the modem via FOTA/OTA application (for example asset_tracker), now without touching the modem could be possible to...
Hello,
Are there any hardware constraints or hard forks in putting an older version of an SDK, such as v11.0.0, on a much newer chip?
I'd like to port SDKv11.0.0 to...
Hello,
Is there any existing firmware where the nRF9160 can act as a coprocessor -- accepting AT commands and the ability to forward LTE data to and from a host application...
Hello, i am a beginner, i am parsing a dimming example. i have two client and server boards, as well as an nRF Mesh application. I can change the brightness of LED by pressing...
Dear Sirs,
I have dveloped application based on the ANT rx HRM example and with nrf52 SD board works perfectly (pca10040(
I would like to move to this application into...
I am using ble_app_gls s130 SDK_11. Is it possible to have pairing with static passkey without bonding? This is because the nRF device will be connected to different smartphones...
I am working on the nr sdk for mesh application,When the nodes conncted to the network , it needs to configured before using nRF mesh app ,My device also configured through...
