I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hello All,
I am working two BLE chipset , one is nordic and another one different make (TI) so is it possible to communicate between two different make BLEs using our nordic...
In NRF 51822 custom board I uploaded ble_app_uart code. Program uploaded successfully. But not able to discover from Phone and Tablet, where in another board it works properly...
hello,everyone.we want to use pin3 and pin4 as txd and rxd,but there has error.could you give us some help?
void debug_uart_init(void)
{
uint32_t err_code;
const app_uart_comm_params_t...
hi,
i made my nrf 52840 dk advertise unlimitedly using ble_app_uart example. connected and disconnected several times using nrfconnect app. it really works fine. with this...
Hi,
I'm using nRF52832 and LDETECT mode for GPIOTE PORT event to detect multiple interruption.
Even though LDETECT mode is described in the product sheet page 112 and...
Dear friends, my current measuing instrument is Power Profiler Kit. I have some troubles when i use it. e.g. 1) how to completely stop an updating plot that a PPK draws? even...
Dear friends, 1) As shown in the pic below, there are some values "max:13.70, min:3.33, rms:3.45..." at the bottom of the pic. which area is these values calculated from?...
I'm finding fairly large lags with the RTC2 I'm using. I use an app_timer to sample the current RTC count value as a timestamp (MM:SS:Hundredth-of-a-second) and send it out...
Hi all,
I have a question to complete the tutorial 'Setting up device firmware update(DFU) on the nRF5 DK'. this
I have tried to set up my nRF51 Development Kit.
Everything...
I am facing wierd behavior after migrating to sdk 10 serialization code i.e ble_connectivity example program. Unable to scan peripheral devices, some times unable to connect...
in SDK14 I'm trying to add an SD card into the BLE central example.
The SD Card example compiles and runs OK. Problem happens when I combine that code into ble_app_uart_c...
Hi,
I'm checking whether SDK 13.0.0 secure bootloader dfu can proceed correctly with iOS DFU library if the process is interrupted because smartphone application is restarted...
Hello,
I want to enable UART only when it is necessary to send data.
I want to use ble_app_uart_low_power_master or ble_app_uart_low_power_slave
The URL of ble_app_uart_low_power_master...
Hello,
I've been working on the ble_multilink example and managed to combine that with the ble_hrs_c example to connect to multiple heart rate units and receive the data...
I create software uart librarty for nrf52832. For one pair tx, rx it's worked (on 9600, 19200 baudrates). Then I create multi-instance software uart (all of them gonna use...
