hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hello,
i am working on nRF52832.
i was successfully build a code for scanning without using FreeRTOS
Now i want to use FreeRTOS with my scanning code
But i am not...
Hi ,
i am using ble ancs profile in my project, i was getting internal error (error no 3) while connecting.
the error is being reported by two of the following event handlers...
I have managed to establish a proper TLS connection with the proper credentials, but it seems that TLS session resumption is missing from my implementation since my device...
Hello:
I am now working with nrf5_SDK_for_Mesh_v3.0.0 and I try to implement OTA for mesh dfu. However, I found that the v4.0.0 has a dfu_no_serial_nrf52832_xxAA_s132_7_0_1...
Hello,
I've just recently started learning to develop on the nrf52 platform after 2 years of frustration trying to learn of how to develop on the Nordic platform I finally...
I am trying to set the Lifecycle state of the cryptocell, but it seems like I am having an issue.
I do
/** Enable crypto cell to configure it **/ NRF_CRYPTOCELL->ENABLE...
Hi,
I have fanstel BM833A modules which is NRF52811.
I am using Segger Embedded Studio.
How can i program the module through segger IDE using ST-LINK?
And also i have...
Multi link ble + zigbee multi-protocol testing is currently underway. The main purpose is to test the packet loss rate and throughput of radio time-division multiplexing zigbee...
We've had so many problem with Bluetooth Smart DFU on nRF52832 that I've decided to write a ticket here and ask for help. We've been reading lots of documentation, following...
We want to change the communication speed for each connected peripheral.
*Environment
Peripheral: nrf52832
Central: nrf52840
*Step 1. After the peripheral connects...
Hi all,
My project will use PPI to control COMP of nRF52832, connect Event of COPM and Task of GPIOTE.
Question 1,
How could I get the address of COMP event and use...
hi.
I wonder if nRF52840 dongle has an unchangeable bootloader, and if so, where we can download it. PCB of nRF52 dongle is available on the official website, but not in...
Hi there,
in my passion to keep up with technological advances, I ordered the nRF5340 PDK. I was hoping to pave the way of moving our nRF52832 and nRF52840 based projects...
