Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi I am using wireshark 1.10.6, when press 'w' wireshark started but it is not capturing packets. even I select my device then also facing same problem. I waited for some...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
I'm still using SDK 12.3 on a nRF52840 product and am bashing my head against the wall because of issues with the USB driver. The current problem is all manner of hard faults...
Hello,
I have been trying to communicate via UART with the Nordic nRF52832 DK (10040) in a Linux (Fedora 26) Guest on Virtual Box. The guest is Windows 7.
The JLink...
I'm in the process of updating from SDK13 to SDK14. In the new CLI, there are a lot of NRF_CLI_VT100_CMD's that are used which weren't there before. If someone is using a...
Worked out of the box. The next day it would not turn ON. Tried charging with and without power switch ON. Charged from an Apple iphone brick and also from a computer USB...
Hi everyone,
I have moved from the cable connection firmware upgrade to the OTA-DFU using the nRF52 dev kit. I am able to download the firmware from nordic's website and...
51822/S130/SDK v12
I was testing prepared Write from iOS to 51822. Write Req/CMD can succeed, but Prepared Write failed with 'Unknown error code 0x82'.
What this 0x82...
I am design a very compact board for my project and running out of space. For this I am planning to replace two DCDC inductors with a single one. Is it possible to do this...
I am communicating with the nrf8001 via SPI, from an HCS08 MCU. First thing I receive:
0x01 0x04 0x81 0x02 0x00 0x02
This makes sense, it tells me it is in setup state...
In my design I am planning to power up some sensors from nRF52832 GPIOs. Is it possible to maintain the GPIO state high during the low power mode of MCU?
Please guide here...
Hello,
I have been testing the BLE multilink examples for the s120 softdevice. More specifically, I have tested the ble_app_hrs_c example in the experimental s120 folder...
Is it possible to configure the parameters of the advertising library (eg. SDK v12.3.0 using SD130 v2.0.1) so that my peripheral device (eg. nRF51) changes after a limited...
I've configured peripheral for broadcast, but why can't IPHONE search it? I don't need APP development. I just want the phone to show it. Is there any special requirement...
