Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hello,
I have a question on how to calculate the capacitance based on oscillator relaxation for NRF52. For example, in the Csense_drv example, when pin is touched by finger...
Hi,
I have a working scanner and manage to require timeslots with the below timings.
Interval 300ms, scan window 50ms, Timeslot length 10ms.
But when i try to...
Hi,
Trying to implement a simple Hardware UART in parrallel with Ble on a custom board with mdbt42 Raytac module. I have the following compilation error:
*** Using Compiler...
I was trying to integrate mesh network into the ble_uart. I am using softdevice v7.3 and sdk6 with nrf51822. I followed the instructions given in the github link text
....
Hi, I bought an Arduino PrimoCore card and I read that you need to buy the Alicepad card. I can not find it on the net. But was it put on the market? Thank you.
Hi,
I have added new UUID (Service and Characteristic) into the uuid_definitions.json but it's not used in the application.
To try I put a error into the json file and...
Initialization:
The softdevice is initialized as in the BLE UART example. The body of the ble_stack_init() function is identical to the BLE UART example.
SPI is initialized...
I have two supplier for provide me nrf52832's based modules.
So I tested it and both is ok. The distance used pcb antenna almost the same (about 80m).
If I use on external...
My application is built using the nRF52832 device.
The system must only be "active" between certain times (5am through to 9pm).
I am a newbie and have no idea how to set...
Hi,
what are the minimal required steps to get the zephyr HCI-UART on a PCA10040 working with Linux BlueZ?
The steps I have so far [My host is Ubuntu 17.04]:
Physically...
Hello,
I am having troubles to run the light_switch example from the nrf5_SDK_for_Mesh_v0.10.0.
I am using PCA10028 boards with nRF51822. I didn't modify anything in...
I basically need clarification on the last point of this question , which seems to imply that:
the first time you call sd_ble_gatts_hvx() while the SoftDevice's transmit...
Hello,
the NFC library provided in SDK (nfc_t2t_lib_gcc.a) is compiled with the FPU support. For specific reasons, we can't currently use the FPU in our project. Would it...
Hi,
I have a problem with advertising, application starts advertising and makes connection normally, but after disconnection advertising is not starting. sd_ble_gap_adv_start...
Hi,
i am using SDK v8.0
and in main function, initialization like this err_code = bsp_init(BSP_INIT_LED | BSP_INIT_BUTTONS, APP_TIMER_TICKS(100, APP_TIMER_PRESCALER), button_event_handler...
