Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
I need atleast 10 UART channels to be configured in my project. Is it possible to do it with the NRF52840. I believe because of the PPI I should be able to do this. I was...
I want to create a small bluetooth device with the nrf52823 chip. I want to use a lithium battery cell to power the whole circuit and therefore it neet to be low power. On...
I'm bigger of NRF52832 and beacon concept. I need modify my beacon data like Major,minor and Tx power change via mobile app configurable. please share any example code or...
I purchased a new nRF9160DK. Upgraded to latest 1.1.0 firmware. I built the AT application and can talk to the modem using the LTE Link Monitor application.
The DK came...
Hi, I'm working on nRF52832 at SDK ver15.3.
My problem is Current consumption increasing (82uA -> 550uA) when WDT Reloading in sleep mode.
I set WDT configuration "Pause...
I am trying to send and receive a response from a machine using Modbus (TTL to Rs485) and nrf51822.
Connections: R0 -> RX(P0.11) ,D1->TX(p0.09), RE&DE->P0.19,VCC->5V
Just...
Hey
We have successfully put the dongle into operation. We were able to develop and successfully test our software.
As soon as we test it with the JLINK on the module...
Hi
I have problem because i dont get all data which are in FIFO uart on my smartphone via BLE. Nrf as i can see in example sends data where data[index-1] == 0x0d || d ata...
I'm working with nRF52832 and playing around with some peripheral examples from SDK 16.0.
The FreeRTOS based heart rate sensor example ( ble_app_hrs_freertos) seems to work...
Hi.
We are using the Nordic UART service. Our project is based on the example project "ble_app_uart" from version 15.2 of the SDK. I've found after about 3 minutes it stops...
So I have been saving a structure using FDS and it seems to be working fine but after a while (2-3 hours of updating value every 10 seconds) the fds_record_update(); function...
CONFIG_MAIN_THREAD_PRIORITY=7
I read prj.conf of mqtt_simple. Why is the value of 7 given?
https://github.com/NordicPlayground/fw-nrfconnect-nrf/blob/master/samples/nrf9160...
Hello,
I am having issues detecting my board with some phones. I have tested it with a Samsung Galaxy S8+, Android 9, and with android 5.1.1. However, I can't detect it...
Hello,
I am using the nRF9160 Dev. Kit and I am getting the following error by trying to load any samples.
Loading solution asset_tracker.emProject Executing load...
