Hey so I just wanted to use the BMI270 on the Thingy:53 and Polling the acceleration values seems to be working just fine. I wanted to use the DATA_READY Trigger. I am working...
Hello,
In ncs, I am working with \nrf\samples\ipc\ipc_service. I want MCUboot to build \nrf\samples\ipc\ipc_service\remote to run on nrf5340 CPUNET. When I CONFIG_BOARD_ENABLE_CPUNET...
Hi,
I am currently conducting measurements using channel sounding with my nRF54L15 boards. I am at the end of my master thesis, so there is not so much time left to really...
The nrfx pwm supports a number of events for a callback: /** @brief PWM driver event type. */ typedef enum { NRFX_PWM_EVT_FINISHED, ///< Sequence playback finished. NRFX_PWM_EVT_END_SEQ0...
Hi,
I have two nRF5340 DKs and want one to be server, one be client. I use NCS offcial code and simply buide them, however, " LED3 starts blinking green on every device...
Hello,
I have been working with the nRF9160 DK to understand AT commands. I tried flashing the Serial LTE Modem application using the Quick Start option in the nRF Connect...
Hi everyone,
In nRF9160 with ncs 2.9.0 I've problems when trying publish a MQTT payload bigger than 2700 bytes aproximately. In advanced I already was adequated buffer size...
Hi,
I tried the nrf51_iot_sdk_0.8.0_f1f6187 and flashed the coap example (examples\iot\coap\ipv6\client\boards\pca10028\armgcc) with the s1xx-iot-prototype2_softdevice...
Hi,
In many places in the nRF51 documentation (e.g. developer.nordicsemi.com/.../a00081.html) the term "Master Control Panel" is used without clarification that this is...
Hi:
i use SDK7.0 , i write data in flash (address:0x0003fc00)and the data is erased when SDK run.
and is there any way to protect the page that i want to write or...
Any recommendations of power ic to be used in an nRF52 based system?
I am thinking of using DC-DC converter from LTC3553 . Is DCDC converters a good choice for powering nRF52...
Hello,
I am basing a design on the reference design from the nRF-DK (pca10028?). I am trying to understand the implications of using an SMA connector footprint for testing...
I tried to get the ANT background scanning example to work on a PCA10028 and it jumps to softdevice_assert_callback when opening the ant channel. Downloaded everything fresh...
Hi Guys,
I'm new to using the nRF51822 environment but I've used AVRs for years, so please be gentle...
I'm wanting to drive a strip of WS2812 RGB LEDs from an nRF51822...
So I have my nRF51822 updating the characteristic value and sending notifications once every time I receive a radio notification.
uint8_t readings[20] = { 0, 0, 1, 2, 3...
I'm trying to set up TIMER0 to interrupt the timeslot 500us before its end.
It doesn't seem like the NRF_RADIO_CALLBACK_SIGNAL_TYPE_TIMER0 signal is happening, I've put a...
When I try to enable SD having earlier initialized Gazell (SD resources variant) sd_ble_enable() returns 2 (SOFTDEVICE_NOT_ENABLED). If I remove the Gazell initializaton it...
I am trying to work with a custom 3rd party BT 4.0 peripheral device which uses an nRF8001 to transmit data as temperature values in the Bluetooth Health Thermometer service...
Hi,
Slight problem here with bootloader updates : right after download, I copy from SWAP (0x16000) to normal location (0x38000 in my case).
sd_mbr_cmd.command = SD_MBR_COMMAND_COPY_BL;...
I am wondering how to precisely measure my power consumption. Till now, I have been using INA216 on PCA10004 board + labView for acquisition, but it is not precise enough...
I was working my way through the app note nAN-36, where it says you should have a seperate source and header file for each service. However in many of the newer SDK examples...
