Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I would like to execute some code when/before sending an advertisement. I tried to do this by using ble_radio_notification_init. Unfortunately for every advertisement...
I'm using the example examples/peripheral/usbd_ble_uart on a nRF42840 USB dongle (pca10059).
As client (central) I'm using nrfconnect on an Android phone.
Connecting to...
Hi, how to link nRF51 IC rev. (1, 2, 3) in NRF51 Series Compatibility matrix ( https://infocenter.nordicsemi.com/topic/comp_matrix_nrf51/COMP/nrf51/nRF51422_nRF51822_ic_rev_sdk_sd_comp_matrix...
Hi everyone,
I am working with SDK 15.2 and Mesh 3.1 with NRF52832 DK.
I am testing the ble app uart coexist example provided by nordic.
I followed the steps provided...
Hi,
I have a problem with Secure DFU Bootloader available from SDK 12.1 on nRF51822_xxAA SoC. I use example in SDK 12.1 and when i download it to nRF51822_xxAA it isn't...
Hello,
I am having problems with a custom NRF52840 Board. My program hands at the ble_stack_init function.
I have encoutered this problem in the past so I have tried the...
Hi.
I try to implement LESC using nRF52810.
But I use a Static passkey because my device doesn't have a keyboard or display.
One question is, is LESC more secure than...
Hi,
I try to use QSPI to communicate with Gigadevice NAND flash http://www.datasheet-pdf.com/Search-Datasheet-PDF/GD5F1GQ4 . There's no DK, the custom board was produced...
Hi everyone,
there is a post dated 11 months ago from now in which Nordic tells that -40dBm Tx power configuration is feasible but not recommended ( Case ID: 230320 ). ...
I merged the code from the SDK examples "usbd_audio" and "usbd_cdc_acm" and have ensured that each has their own INTERFACE and ENDPOINTS. I am able to download to the development...
Hi,
I am developing with nRF52832, SDK 15.3
I have an issue with sending data over NUS service. When I flash the code to nRF, it starts advertising, but when I connect...
Dear sir,
The twi sensor code in SDK14 is getting stuck at NRF_BREAKPOINT_COND. Also, on the uart terminal it is showing FATAL ERROR . Please help me out of this.I am using...
Hi
I want to set up a network of about 4 groups of BLE light modules(using the experimental dimming example). Each group comprises of 5 to 7 light modules.
Currently the...
Hello, my code was working just find then I tried to add the user description value to my characteristic. In the example below I had set it to "Test" for now. Once I did this...
hi
i am programing BLE blinky app blinky which advertise. yes, the same code i am trying on custom board works on nrf52DK which has LFRC crystal activated as mentioned on...
