Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hi DevZone,
I am new to nRF SoC and SEGGER. After installing all tools, I can build and run examples.
I run into a problem to add and enable a nRF driver, like "UARTE...
Hello, I am trying to develop a rehabilitation exercise service using Thingy52.
Thingy52 is the only device to accomplish my objective which needs motion detection using...
Hi,
I have nrf52840 DK and PCA63511 Power Profiler.
I have two questions:
1. The Average Current Consumption measured with profiler is 110uA (18 mA max, over 10 s...
Hi,
I have Raspberry pi board which i want to use it as a gateway .on which server will get set up.
nrf52840 will be the beacons which i have already set up for sending...
I am trying to use the NRF connect mobile app on android 8.1.0 to try and connect to a Bluetooth server serving GATT request to verify functionality.
The server is running...
Hello,
I am using these pre certified modules https://www.nicerf.com/product_147_88.html in a project which is basically nrf24l01+ with a PA and LNA.
These support ...
Hi,
Just been testing the data rate of write without response commands, I'm only getting about 250 bytes / second which seems incredibly slow?
I've just got a simple little...
Hi,
Is it possible to route an analoge signal through a digital GPIO pin to access the inner analoge pins of a nRF52840? I want to avoid using via-in-pad to keep the cost...
Hello,
I can't get the hex file to come out correctly in segger studio. What happens is, I build the solution and create the hex file but when I go to program my device...
Environment - nrf52832 - SDK 15.3
- SD 6.1.1 - with FreeRTOS
- Project: ble_app_buttonless_dfu
I have project with 4 timers and 3 tasks. Everything works fine when...
I have made changes from here in order to configure data rate at Coded PHY for mesh application.
Tested with two phones: Moto G5 Plus (Bluetooth 4.2) OnePlus 6 (Bluetooth...
Hi,
I am tring to display some information using NRF_LOG_HEXDUMP_DEBUG(). However, I can't see anything on the terminal. If I use NRF_LOG_INFO("xxxxx"), I can see the...
I'm using two nRF52840 DKs with SDK 16.0 with one as a central, the other as a peripheral. I'd like to setup an IRK whitelist on the peripheral. I've taken a look at the hid...
Hello,
I'm having trouble getting my program to compile with the SAADC. I started with a BLE template then added the battery service with sensorsim from ble_app_hrs and...
