I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
My configuration:
NRF51822 v2
TWI
GPIOTE
Issue:
The gpio interrupt does not get triggered. I know that my twi device is changing the state of the gpio3...
Hello, I apologise for this being quite simple as questions go but I was wondering if anyone knew where to begin or if there is any good information out there on how to use...
Hi,
I need use the nrf51822 to connect to PC via usb ble adapter (virtual com port).
The PC side has the USB BLE dongle (adapter).
http://www.amazon.co.uk/Plugable-Bluetooth...
Hi....
Is there any issue in sending a value on a character in button_event_handler? When i tried it disconnection is happening.Am not using button service , just using...
When running the makefiles found in the esb/gcc_rx and esb/gcc_tx folders I get the following errors:
base:gcc_tx jnoble$ make
mkdir _build
"/Users/jnoble/hardware/nrf51822...
I have trouble compiling successfully even the simplest of example codes for the nRF51822 with the Keil MDK-ARM toolchain (v5).
For example, for the "blinky" project, I...
I have ported the example ble_app_beacon from sdk 7.2.0 for use with nrf51422_xxaa and softdevice s310 (v.2.00).
In the function ble_stack_init() there is a call to the...
Hello everyone,
I have two doubts related to pca10001 board:
What is the maximum amount of current
that can be pulled from a single GPIO
pin?
Does the...
Hello,
I just received new rev.3 nrf51822 chips, so I am migrating with my project to newest SDK version.
I installed Keil5 with that smart run-time environment manager...
I would like to send the current status of the battery as a beacon.
ADC and a few resistors and what do I need?
I am currently using nrf51822.
I know nrf51822 to...
I'm trying to port my old project to the newer soft device and SDK (v8.0.0) and just ran into an issue where the app_timer_event_t seems to no longer be defined. My previous...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Is there a UART version of the DFU example that is provided with the new SoftDevice 7.0?
If not how to go about modifying the BLE DFU example to be able to handle UART...
Hi, I made a beacon board only have button and leds. The version of chip is nRF51822-QFAA G0. I used the precompiled hex file in the nRF518222 Beacon v1.1.0. After I download...
Hi,
I am trying to debug a custom PCB for the NRF51822 - I can run a modified version of the HRS application (S110) that has been verified on the PCA10004. The LF clock...
