Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
I try to use Android studio to build nRF Beacon project,but it didn't work ,and there are several error .
the error is
Error:(50, 35) No resource found that matches...
Hallo,
I try to use the s310 timeslot API. I open a "session" and then request a timeslot:
check( sd_radio_session_open( nrf_radio_signal_callback ) );
request_radio_slot...
I am trying to implement the pulse counting mentioned in a previous post of the same name, but the code is eluding me. I am using the heart rate service example with new code...
Hello,
I want to implement a firmware update over ble for my application and the SoftDevice 130. Which would be the correct boatloader.hex that I should use? I am working...
Hi,
I am using softdevice-7 and SDK 6.1 for our application.
If I connect using a passkey, first 「BLE_GAP_EVT_SEC_PARAMS_REQUEST」 event occurs, then the 「BLE_GAP_EVT_PASSKEY_DISPLAY...
I have a mature design with several hundred units built using QFAAE0 silicon. Code works. Hardware works. FCC is happy.
I'm considering migration to V3 silicon and maybe...
Hi....
I have PCA10028 DK and i want to make a profile that works both as central and peripheral. As a part of this i tried running S130 demo app found in S130_softdevice...
I need to remember the CCCD's of some service, e.g. service changed. A CCCD is according to spec 2 bytes long. The method to do this is by using sd_ble_gatts_sys_attr_get...
Not sure why but my time is only firing at 250Hz with the prescaler set to 0. Not sure why. Shouldn't it be going at 16Mhz at these settings? (Running on the PCA10028 Board...
Hi,
I am using device as ble-Peripheral SDK nRF51_SDK_7.2.0_cf547b5 and softdevice
version :s110_nrf51822_7.1.0_softdevice.
problem : I am receiving data on Nordic...
I'm trying to use the internal temperature sensor of the nRF51 to know the die temperature. Its accuracy is specced as +/- 4 degC, even +/- 8 degC at the extremes. Does anyone...
Hello,
I am trying to control the smart phone function while making my device as HID keyboard, but It seems that the soft keyboard (smart phone on screen keyboard) clashing...
i think your nrf51 iot sdk don't have rpl functionality....
if i want to implement rpl on it what is the procedure...
if i want rpl on raspberry pi what is procedure......
