Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
We're moving our design from nRF51822 to nRF51422.
What's the difference between these IC from the point of view of PCB layout and antenna design? Are they interchangeable...
Custom Board with MCU NordicSemi nRF51822-QFAA
Softdevice S110 7.1
IAR for ARM 7.1
SDK 7.2 using a merged service (HID keyboard example + NUS example...
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
Hi,
Are there any available examples of Makefiles with JLink command integrated?
Example: "make flash" to flash the image or "make flash-softdevice" to flash the softdevice...
It's not really a question but a request to Nordic.
Could you change the #ifdef lines in gcc_startup_nrf51.s to .ifdef. So:
.ifdef __STACK_SIZE
.else
.endif
and...
Hi,
How do I determine the application address? The one that is to be programmed to UICR.CLENR0.
I have SD S110 V7.1.0 but I didn't find this information in the release...
Hello,
I receive NRF_ERROR_INVALID_STATE error quite a few times because my own state handling is still a little buggy. I want to find all these errors. What would be the...
Hi all,
Please I want to make sure of something. In the s120 specification, it's written " Bluetooth low energy combined Central and Peripheral SoftDevice", and even in...
Hello,
I need to read the UID and later on also the RSSI value of devices (Handys) in range.
It should be reading the values automatically without the need of manual connecting...
The datasheets for the nRF24LU1P ansd nRF24LO1P have near identical example antenna driver designs which vary in the values for the inductors, etc
The LU1P datasheet is...
Hi,
I've combined twi_sw_master and DFU in my project based on nRF51822 Beacon v1.1.0. Now I can't connect to the beacon. The same project only with DFU or only with twi_sw_master...
Error is shown in the following figure.
I use nrf51822-DK(256k)
The exception of BLE_S110 works well.
Memory Is not enough when you add a BLE_S110
Is there any...
I am using S120 v2 with SDK 6.
Initialization of the softdevice and device manager return no errors.
However when I want to start a scan for devices, the function checks...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
