I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Based on SDK15.3(nRF52810) app_uart example, stop the adverting, turn off all the peripherals and enter idle_state_handle(), but the static current is still about 10uA. Rememeber...
I set up the environment for the nRF9160 as it was specified and downloaded the git-hub code https://github.com/NordicPlayground/fw-nrfconnect-nrf (environment 1) and I tested...
Hi all,
I am using 2 SPI's in my design. I enabled SPI0_ENABLED and SPI1_ENABLED in my sdk_config.h.
SPI0 works fine. But SPI1 MOSI pin always sends 0xFF.
My pin configuration...
Hi, I m sending a packet in mode Nrf_1Mb to another board nrf5340-PDK.
When I try to enable NRF_REGULATORS_S->VREGRADIO.DCDCEN=REGULATORS_VREGRADIO_DCDCEN_DCDCEN_Enabled;...
Hi,
I am using mesh SDK v3.2.0 and SoftDevice(s140 v6.1.1) to build light switch server firmware. And also insert the uart code from nRF5_SDK_15.3.0_59ac345. So the light...
Hello:
I am studying thread samples in nRF9160.
There are two thread samples: "zephyr\samples\basic\threads" and “zephyr\samples\synchronization”.
But I can't find main...
Hello,
I received information that i could turn the modem on and off not more than 60 times within an hour.
We are however working on a real time system, which may...
Hi everyone,
Currently I am routing hardware for an upcoming project using the nRF5340 and it's time for a sanity check.
The goal is that the HW works well enough w/Engineering...
Hi,
I've been trying to set up a SPI <-> USB interface between an FPGA and my PC via the nrf52840 dk. My ultimate goal is to stream 1Mbps+ worth of data, but right now I...
I have a custom characteristic on which I send ASCII strings as notifications similar to NUS. Is there a way to have the Bluetooth Low Energy app in nrfConnect show the data...
I am writing a BLE application on the nRF52832 using S132 v6.0 and SDK 15.2, and my application is using the nrfx_SPIM driver. I find that once I initialize the spim driver...
I am using the nRF52840, SDK 16.0.
I'm attempting to advertise on the coded phy and the 1M phy simultaneously. This works.
I have two phones, one that supports coded...
Hi,
I tried to enable the CMSIS in my CUSTOM Project but I see the following error and the CMSIS configurator is empty. Please guide what would be the possible problem....
Hardware: nRF52840 DK
SDK: 16.0.0
FreeRTOS: 10.0.0
I am attempting to use UARTE1 for a Modbus port. UART0 is already in use for a Command Line Interface. I can set up...
