Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hi,
I´m trying to flash a custom board with nrf52833 chip with the nrf82833 DK.
How can i make sure, that tha DK board will program the custom board? Currently it...
Why isn't this working?
The MPU_RESET_PIN is set to : NRF_GPIO_PIN_MAP( 0 , 20 )
I can not seem to be able to alter the state of the PIN. Whenever I read the PIN its...
Hello all!
I have a timer that sometimes gets started inside the IRQ of the ESB and sometimes needs to be restarted inside its own IRQ
I'm running it in a "one shot...
Hello
This parameter must be modified e.g. if you have a large number of characteristic in your custom service.
is there a reasoning to calculate this or just "try and...
Hello,
We are developing on the NRF52840, using SDK 15.2.0 and FreeRTOS
We currently have DFU over BLE implemented, but we are strongly considering switching over to DFU...
Hello,
we are developing a firmware for the nRF52840 which requires the use of Bluetooth and the SPIS (SPI Slave) functionality.
We are using S140 & SDK 16.
We encounter...
Hi,
I'm having an issue with using nrfutil to generate a bootloader settings image for loading onto an nRF52840 MCU. The resulting image appears to have the wrong starting...
The SERIAL_OPCODE_CMD_CONFIG_TX_POWER_SET (0x44) is not supported in mesh SDK v4.0.0, so I added the following in the file serial_handler_config.c
#include "core_tx.h" #include...
Hi,
I have an application that needs 256kB of RAM however when I try to compile the code for the application processor it complains that there is only 64kB available....
Hi, I've created a custom service for my application. However, is there any way to give a name to the corresponding UUID? I want the custom UUDI to be appearing for example...
Hi,
I updated Segger Embedded Studio to the latest version, 4.50, after that it asked me to update JLINKv6.62a firmware update, but there after I had problems with the board...
Cortex M33 applications on the Thingy-91 - are we able to write any application program that would normally run on a standard M33 ARM processor (off the shelf) - or are there...
Hi I m new to Nordic products and I m just evaluating the nrf5340-PDK.
is it possible to enter in SYSTEM OFF and wake up the CPU with RTC0 or RTC1 interrupt?
How To do...
Hello to all. Is it possible to send and receive data between 52840 dongles using ZigBee? I need a simple program which records data in one dongle and sends to another. Thanks...
Hi :
Our project(SDK15.2) use the uart DFU to transfer the firmware , usually when the firmware has been transfered ,it can jump to app successfull .But Sometimes,bootloader...
