Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
I am trying to implement a REQ line protocol over GPIO to signal to the Master when it is ok to receive data. Basically, I want to pull the REQ line high when the nrf51 has...
Hello,
Ble spec says that "new alert" characteristic - field: "category ID" can have 1 or 2 bytes.
here
But it seems in your struct you let it have only 1B.
typedef...
Hi,
I have ordered a PCB using the reference schematic for NRF51422 user guide.
I wanted to know whether the schematic has the required antenna design or I need to add...
Hi All,
I have a basic question about advertsing data, more precisely about device's address.
I try to disable in my advertising data, the address field but it doesn't...
Hi I followed the Nordic UART example code to read and write characteristics to a Nordic S110 nRf51822 device.
My code is the same as in writeRxcharacteristic but when...
When I'm single stepping my nRF52 application in Keil with a BLE connection I always get the softdevice_fault_handler called.
I'm using SD 132, v2.0.0 and the the parameters...
What is the maximum clk frequency that can be output on a gpio for the nRF52832 ? I want the nRF52832 to output a clk signal on any of the gpios to an external module, and...
Can anyone please suggest a simple example on initializing SAADC Driver on one pin and do a simple blocking ADC read?
Sorry for a very broad question - but rather to ask...
I'm using the nRF52 Dev board and set the --rbp ALL option while using nrfjprog. It worked fine, and I am able to do OTA updates as I was testing the bootloader example. But...
Hi
I'm doing one project that is taking data from uart and send to mobile app. I'm facing one issue that is when I connected to peripheral it connected and take data from...
I'm looking for some options to extend the PCA10028 with a keybord and a numpad. This would give great options to play around with passkey topics.
As the PCA10028 supports...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Hello,
I am trying the ANT-OTA DFU Update using an ANT Stick and the nr51422 pca 10028 board. The ANT Updater shows that the Image Upload is completed. I am uploading the...
Hi,
I there a way that I can detect if a sections of my code has been interrupted by the Softdevice? I have some time critical code (bit banging a communication protocol...
Hi All,
I am using the nrf51422 and softdevice S310 to send out ANT+ and BT Smart in my project.
I use RTC1->Counter in order to get a timestamp for an interrupt from...
