I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
A source program, with another computer compiled to generate HEX files, download to the NRF52832 development board, GPIOTE function can work properly. But the same source...
Please point me in the right direction if you can, I'm stumped. My project is based on the app_hids_keyboard sample, using the pca10040 board (nrf52832) and SDK 14.2, soft...
I want to store some data, so I first write the initial data, then update it again and again when need. I think the record_update function should new a copy of the old data...
hi all
I am facing the issue that the chip still retains in debug mode. SWDCLK pin has connected to GND directly.
steps:
1. after flashed hex file, removed debugger...
Moving from SDK14 to SDK15, I noticed that USB takes long time to make connection (20 - 30 seconds). Comparing nrf_drv_usbd.c, I realized that the "shortcut between EP0DATADONE...
Hi Nordic team
I want to switch between DTM and normal BLE by pressing the button.
It is base on two example ble_app_att_mtu_throughput and direct_test_mode.
Is there...
Hi,
My central device should scan and should get DIS of one peripheral and store in central and central should pass this information to other peripheral .
or
Central...
I am using nRF52832 with Beacon_App. I can able to get UID, Major, Minor, RSSI from my Raspberry PI using Python code.
I want to calculate the distance between my Raspberry...
I'm using S112 and SDK 14.2 to target NRF52810, but using the PCA10040 DK for now.
I've been coming back this issue multiple times over the past couple of months, still...
Hi @ll,
I tried to get the dfu example up and running but there are a lot of problems I encountered:
- Using the device_page_generator.py the string for the public key...
Hi @ll,
I have a problem bringing the pyaci up and running.
I used it successfully for everything before but since today it is making a mess again:
When I'm trying to...
I am using secure dfu bootloader from the SDK 12.
I changed the start address of my application. In the bootloader, in uint32_t nrf_dfu_init() { } , calling function nrf_bootloader_app_start...
Hello,
I want to make a simple UART Bridge between Central and Peirpheral. I'm usign nRF52832 with nRF5_SDK v15. There are central and peripheral uart examples in the...
