I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hi,
I have modified the nus service and added two new characteristics called txs and rxs which support read and write protection.
on the peripheral i have set BLE_GAP_CONN_SEC_MODE_SET_LESC_ENC_WITH_MITM...
Hello:
According to the website, please nrf52832 circuit design, without adding other peripherals, just as a radio Beacon, button battery voltage at 2.3 V nrf52832 cannot...
Hello, I am using SDK 15 & Softdevice 6, I am using NRF52840.
I have merged the USB CDC into a multi-link example. I confirmed that it worked, and the project was successful...
Hi
Is the DCDC enabled or disabled by default when using the DTM example in SDK v15.0.0? We can't find any reference to it so we assume it is disabled, but just wanted...
Hi guys,
On my application, I ported the code from TWI_scanner example (SDK14) and it is connected to a temperature sensor the which is read every 45 seconds, It is working...
As far as I can tell, Shockburst isn't officially supported on the nRF52840 in SDK 15. However, I have seen some success from others with this configuration, but after making...
Hi,
I have been working with the NRF52832, and trying to capture raw ADC data with the help of TWI bus. I have imported the necessary libraries (i'll attach the code below...
I have used aes_all_cli example to test computation time for AEAD EAX/GCM/CCM. I have shortened the plain text to 16 bytes, added pin toggling on encryption function enter...
I don’t have a lot of information as I’ve been totally unsuccessful in debugging this.
In short, we have a SPI peripheral that was working under SDK 14.2. Under 15.0 we...
Hi,
I am trying the connect MIO Fuse heart rate band. It follows the standard specified by Bluetooth SIG i.e Heart rate profile UUID is 180D and the heart rate measurement...
I'm currently woking on doing my own DFU system, the system should work this way : the central gets a new version of the app via the internet network and it should update...
How to establish communication with a peripheral through I2C ?what are the functions needed to define address and write and read from the slave address
Hi,
I followed the instructions for importing the Thing:52 firmware into SES and managed to get the firmware compiled and loading, and the code reaches the main function...
Hi,
I'm following DFU quick start guide and I'm using mesh SDK v2.0.1, I have a problem in step 4 wheere I need to generate a hex version of device page, I did this :
...
