Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi,
I am using a 24L01+(as PTX) communicating with a nrf52832(as PRX).
I can have these two device communicating, where nrf52832 can receive data from 24L01+.
However...
I am using SDK 15 and i have successfully flash soft device , boot-loader and application code using nrfgo studio. Connecting using nrf connect application. Click on the DFU...
Hi,
We are transitioning a product from the nRF51 to nRF52832, and I am looking into what I need to do to get our code ported over and approved with the Bluetooth SiG. ...
Hi there,
I am a using a nRF52/SDK 13 to communicate to an external board which uses AT commands, I would like to save some battery during the time I perform my AT command...
I read that the old SDK for mesh had the provisioner and client as the same operation, as I am trying to make my own philips hue style wireless lamp I would need to get my...
Hi!
My question is for the purpose of power calculations for both the nRF52832 and nRF52840 for BLE use only.
I haven't been able to find a reference for this.
I see...
I'm trying to follow "Bluetooth low energy Advertising, a beginner's tutorial" by MartinBL found at https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble...
Hi, in my previous attempt to fix n52DK, I fixed the n52DK board's power rail. It turns out not the problem of the interface MCU shorting VDD.
But when I followed the instruction...
Hi All,
Just feedback from Lab, they said that they can set any channel frequencies at bandwidth = 1MHz in the Direct Test Mode. BUT they said that they need to test any...
Did someone try to make QT application that supports DFU for BLE devices? Can it be done using nordic DFU android/ios libraries (to include them somehow in QT project)?
Hi,
I am having a problems with USB enumerating with a custom board based on the nRF52840. The board is self powered by LiPo battery. I am developing by connecting to the...
Greetings,
I'm attempting to use the ble_connectivity example for the PCA10040 and have a couple questions:
1) What are the default GPIO pins for UART?, for SPI?
2)...
Can you provide an android application that can implement light control?A s shown in Illustration:
like the nRF Connect or LightBlue.the application as client not provisioner...
HI：
I am studying mesh now.But I don't know how to run this example.I think，that proceed as follows：
1.Using provisioner example Configuration each node(element and models...
