Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I write the code almost ok.
but , I neet the DFU function to UPDATE THE software .
Now, we only find a v11 example can run ok but only a zip, not including any code. ...
Hello,
First of all, I've read the entry below.
devzone.nordicsemi.com/.../
My questions:
1 - If I cannot advertise for only specific masters, how can I provide...
Hello!
I have a problem with NRF8001 modules. I have two similar boards - one with NRF8001C and another with NRF8001D module. NRF8001C board works well, but NRF8001D board...
Hello all, at present time I'm making investigation of BLE link stablility at harsh megapolis environment and at long open space ranges. During testing I found out some information...
Looks like there is an error in the nrf_drv_gpiote_common.h :
#define INTERRUPT_PRIORITY_VALIDATION(pri) STATIC_ASSERT(((pri > 2) && (pri < 4)) || ((pri > 5) && (pri <...
Hi guys,
So as I'm migrating from SDK10 to SDK12 I've noted that the app_pwm module is consuming more power then expected while disabled ~300uA. After initialization, I...
Platform: nRF52-DK using SDK12.1.0 and S132
Summary: Using nrf_log module from SDK along with RTT by setting NRF_LOG_BACKEND_SERIAL_USES_RTT flag causes nrf_log_serial...
For example, in SDK11, the file:
components/softdevice/s130/toolchain/armgcc/armgcc_s130_nrf51822_xxaa.ld
Contains:
RAM (rwx) : ORIGIN = 0x20000000, LENGTH = 0x4000...
Not a question, but a big thank you to Nordic Tech Support (Kristin) who reviewed our nRF24 design several times until we got it right :)
Implementing the recommendations...
Hi,
I am creating the first prototype for my BLE product and for now I used the suggested layout from the datasheet, but I am kind suspicious of that layout it seems very...
I follow the example, as below
nRF5_SDK_12.1.0_0d23e2a\examples\peripheral\flashwrite
but I only get some error, can not get anything, and the ble is unconnected.
Hi there. I'm making a sensor system which is intended to measure an ADC value, and send it using the Heart Rate Sensor template. To make this, I've rebuilt the ble_app_hrs...
Hi
Does the newly released nRF52840 chip have pins on the side, corresponding to the "outer ring" (A8-23, AD2-23, B1-W1, ...) pins on the underside of the chip, like this...
hello i am interfacing i2c sensor mma8452 with nrf51 dk. my function is
void mma_read(uint8_t *x, uint8_t *y, uint8_t *z)
{
uint32_t err_code;
uint8_t rx_buffer...
