Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
I have a weird question:
On the nRF DKs (51&52) there are pin headers to connect them to an Arduino.
When delivered, on these headers there are some sort of plastic clamps...
As I working on a new project I am writing the code to support the new SDK driver structure and not including any "legacy" code support.
This highlights the fact that the...
I have a custom board with nrf51422-QFAC, used with SD 130 and SDK 12.3.0. My firmware consist of ble_app_hids_keyboard example modified. Schematics are attached below.
...
Hi all,
I using 1 Provisioner provisioning for some Nodes (light switch server) . If I have 5 Nodes in mesh network
I want to remove Node 4 from network and then add it...
I am working on a BLE peripheral (nRF52832 & SDK 15) which uses the Peer Manager to handle encryption and bonding to a previously existing central device. Sometimes bonding...
I am using the Segger Embeded studio and wondering about the SWO output.
I know I can load code and set break points with just SWDIO and SWDCLK.
So with RTT do I really...
HI all,
I'm working on the nrf52840, and I've tested this on the devkit as well as on-board on the product I'm working on. Using the saadc, if I tie my AIN line to VCC...
My use case initially is a single central sensor server powered from the mians and serving by BLE one battery-powered peripheral that has one of the commonly available st7565...
Hi,
MacOS serial device name is changings all the time when the nrf52 DK Eval board is re-powered. Meanwhile I have /dev/tty.usbmodem49, counting up. Next time I re-power...
We want to be able to download a firmware image into external flash through multiple paths (wireless or wired -only one path is used at a time) then program that image into...
Macbook pro mid-2014
High Sierra 10.13.5
I get the following message when trying to select the PCA10028 on the serial port:
2018-07-06T22:53:49.427Z INFO Application...
Hello all,
Thanks to the wonderfull nrf connect android app, I've been able to setup a BLE peripheral to broadcast the standardised service for "Location and navigation...
I'm digging into OpenThread, using the NRF52840 DK. I find myself spending most of my time trying to figure out module dependencies. Is there any way to quickly get all the...
I was experimenting the nRF connect android app and switch to the DFU service mode. But now, i am not able to switch it to the default mode. kindly help..
Hi,
In softdevice spec, we have the following figure.
However our bootloader code shows that MBRPARAMADDR is 0x7E000 while BOOTLOADERADDR is 0x78000. In this case...
