what can be the starting Point for Bachelor Thesis involving BLE 5.0 devices to be deploy in mesh Network. How the challanges in the Thesis can be address and set as a Goal...
Note: This is related to the following issues:
- https://devzone.nordicsemi.com/f/nordic-q-a/63255/nrf9160-getting-stuck-after-cell-change
- https://devzone.nordicsemi...
Hi, I am Product Manager working for Medical Device Manufacturing company based out of Ireland.
we are in search for a development house / developer who will support us...
I have so many versions of this topic that I now am certain that most of the answers provided are wrong. Since you cannot have so many ways of connecting an external nrf device...
Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
Hi
I would like to perform a connection over 2MPHY instead of 1MPHY; is there an example to show this? This should be doable according to the softdevice v6.1.0 changelog...
Dear Nordic
I am doing a project that has a multilink one central and ten peripherals.
So I started with ble multilink multi role in here . I added ble_nus_c and uart...
Hello everyone,
I am developing a ble device and cant get under 7mA.
For test i used example application. BLE Beacon example. And the hardware part is realy basic. Only...
Hi,
We need to design a network with one master and 36 devices connected, with "long range" capability, exchanging sometime messages from 100 to 4000 bytes.
The number...
I understand from forum post https://devzone.nordicsemi.com/f/nordic-q-a/19250/the-number-of-central-connections-in-s140 that S140 v5.0.0 1.alpha release supports 8 concurrent...
I understand that Nordic provides a proprietary DFU via the BLE mesh. What mechanisms are in place to ensure that all packets reach their destination, e.g. acknowledgements...
-Using SoftDevice S110 8.0.0 for the nRF51822_xxAA.
-UART0 running on 19k2 without flow control (only rx/tx) and using irq priority APP_IRQ_PRIORITY_LOW (=3)
-Using the...
I'm currently porting my code from nrf52832/S132 to nrf52810/S112 (SDK14.2).
It seems that the s112 has no support for scanning, i.e., BLE_GAP_EVT_ADV_REPORT, sd_ble_gap_scan_start...
Hi,
I am working with the 52832, writing values on the flash and I'd like to make sure that I have done it correctly, the correct values are where they should be.
Is there...
Regarding range through human body, is bluetooth 5 coming with real improvements ? Can anyone testify ? for example, for a sensor behind the torso in the middle of the line...
Hi All,
I have been busy trying to get my application programmed onto my NRF52 dongle by using the Nordic NRF52 DK board as a Segger debug/programming interface. All was...
I want to design NRF52832 with 2.5 VDD and connect to an UART IC (CP2012),
unfortunately, "CP2012" just work in minimal 3.0V.
So, here is the question,
When NRF52832...
Hi,
I have recently tested some commands from the radio test example given in the following link using a PredevKit for the nRF52840 and it was quite fine:
http://infocenter...
Hi.
I'm struggling with BLE example projects on the my custom board.
my board uses nRF52832-QFAA, 16MHz external crystal with no 32,768kHz optional RTC.
and I choose...
Hi,
I am developing software supporting LEsecure using SDK 12.3 with nRF 51822.
There is a shift to SDK 15.0 as a measure against "nWP - 031", but can not cope with nRF...
