Hello,
We are working on establishing a connection between one of our existing Bluetooth modules (cypress) and nordic based module to provide backward compatibility with...
We are developing HW that includes nRF9151 running DECT NR+ with the Wirepas stack for mesh connectivity between multiple units. The product is expected to move between geographies...
Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
Hi,
I am working with the nRF54L15 and I want to use it both as a BLE central and as a BLE peripheral. So, I have two separate source files: one for central and one for...
Hi all,
nrf54l15dk,v3.0.1,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
Finally...
We use several Nordic chips in our BLE sensors. We bond to the devices from Android, connect to update configurations, then disconnect such that the device then advertises...
Hi ,
can u please provide more details about error code 4, returned by ble_ancs_c_init function.
what is this error, and how to resolve it???
thanks,
amarjeet
Hi there,
we are developing an application based on simple IEEE 802.15.4 packets, for which we use the radio peripheral. Every example found in the SDK starts with switching...
Hi
I would like to perform a connection over 2MPHY instead of 1MPHY; is there an example to show this? This should be doable according to the softdevice v6.1.0 changelog...
Dear Nordic
I am doing a project that has a multilink one central and ten peripherals.
So I started with ble multilink multi role in here . I added ble_nus_c and uart...
Hello everyone,
I am developing a ble device and cant get under 7mA.
For test i used example application. BLE Beacon example. And the hardware part is realy basic. Only...
Hi,
We need to design a network with one master and 36 devices connected, with "long range" capability, exchanging sometime messages from 100 to 4000 bytes.
The number...
I understand from forum post https://devzone.nordicsemi.com/f/nordic-q-a/19250/the-number-of-central-connections-in-s140 that S140 v5.0.0 1.alpha release supports 8 concurrent...
I understand that Nordic provides a proprietary DFU via the BLE mesh. What mechanisms are in place to ensure that all packets reach their destination, e.g. acknowledgements...
-Using SoftDevice S110 8.0.0 for the nRF51822_xxAA.
-UART0 running on 19k2 without flow control (only rx/tx) and using irq priority APP_IRQ_PRIORITY_LOW (=3)
-Using the...
I'm currently porting my code from nrf52832/S132 to nrf52810/S112 (SDK14.2).
It seems that the s112 has no support for scanning, i.e., BLE_GAP_EVT_ADV_REPORT, sd_ble_gap_scan_start...
Hi,
I am working with the 52832, writing values on the flash and I'd like to make sure that I have done it correctly, the correct values are where they should be.
Is there...
Regarding range through human body, is bluetooth 5 coming with real improvements ? Can anyone testify ? for example, for a sensor behind the torso in the middle of the line...
Hi All,
I have been busy trying to get my application programmed onto my NRF52 dongle by using the Nordic NRF52 DK board as a Segger debug/programming interface. All was...
I want to design NRF52832 with 2.5 VDD and connect to an UART IC (CP2012),
unfortunately, "CP2012" just work in minimal 3.0V.
So, here is the question,
When NRF52832...
