Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
test1.hex
1.png
2.png
When i used board 0 extension board to program nRF24LE1 QFN24 OTP/Flash. it notification of error "An error occured when programming the infopage...
I'm looking for information about bandwidth utilization in crowded environments, something like a sports stadium.
Has anyone at Nordic collected data on potential congestion...
I write some function, it can run ok before I start he BLE function.
When I start the BLE function, the function can not run ok.
but , I get some data from APP throuth BLE...
Hi,
I've written code to use the "gpiote in event" to sense an interrupt from a peripheral (acceleromenter), but as soon as I enable the in event, I notice the current...
Hi everyone,
I was having RAM overflowed with stack issues which were resolved using suggestions here . Now I am facing another issue. While running mqtt I can only do...
I am trying to use the Scheduler to create my own event handler system (similar to a Ti 8051 OSAL system). I'm writing separate classes that can push data/trigger handlers...
Hi,
I use the BDS v1.1 and nRF Plugin 1.2.2 (from 23.Dec.15). My goal is to simply generate a code for the cycling power profile defined by the Bluetooth SIG. I dont change...
Hello, in the NRF Toolbox UART application for iPhone if you navigate the the UART button screen and connect to the nrf52 eveything is fine. You can exit the app (whitch goes...
After some days trying a very simple tx/rx, reading each page of the manual, looking at at this developer zone, etc. I´m still in trouble, with many distinct partial results...
Hi,
I have a problem with my SPIM read buffer.
As you can see below, my SPI device received bytes correctly and answer correctly
My code is based on SPI example...
In the simple_uart.c there is a code:
void simple_uart_put(uint8_t cr)
{
NRF_UART0->TXD = (uint8_t)cr;
while (NRF_UART0->EVENTS_TXDRDY != 1)
{
// Wait for the...
Hello. I wanted to use a receiver on a quadcopter and some becons nearby(+-5 meters). Is it possible to determine the distance IN REAL TIME to the drone?
