hi dear nordic employee:
I tried to build the project ble_app_hrs_c(pca10040) by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit(nrf52832)
2、what is my purpose?
the quality of thingy52 audio demo is not good(iphone7)...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi:
As we are going to use nRF52840 on our product, we were trying the check the HW security implemented in the chip. nRf52840 implemented Arm TrustZone CryptoCell-310 in...
Hi Team,
I hope you are doing good.....
I am using nRF51822 with the SDK version 12.3.0 in windows, keil version is 5.26.
In the blu_app_uart Application i want...
Hi,
In order to isolate the issue, I've created an app that :
1. switches to dc2dc mode.
2. calls sd_app_evt_wait()
I still see 3ma consumption,
any ideas...
Hi
Actually i have a big project and have a problem in the estimation of FLASH and RAM memory for the project
i ma going to implement the mesh SDK with the BLE Stack because...
Hello,
I am working with a custom board with the nrf52832 chip.
I have merged and written the following on the board: SD (s132, 6.1.0) + secure bootloader from the latest...
Hello,
I purchased a nRF52 DK board and sparkfun nrf52832 breakout board , and was successful with blinking the LED on the breakout board.
In order to test if I would...
Hello,
(I am using SDK 15.1 on a linux system)
I will breakdown the question in two parts -
when do we get fatal ? - i know one or two cases for example when softdevice...
Hi.....
i want to transfer the data for every one minute from peripheral device to nrf connect via (phone app).. how to declare in the program and what function to be used...
Dear all,
When I added more than 4 buttons by modifying the example "ble_app_uart" of nRF5_SDK_15.2.0_9412b96, nRF52832 can not run normally.
Another strangely problem...
Hi,
Just got four 52840 USB dongles, with the intent to evaluate the Nordic BT Mesh. But I've been unable to get even a simple Blinky example programmed on the dongle. I...
Hi all, I've just implemented light switch proxy example and it's working very well. Now, I have three NRF52832 boards, and for instance, I have:
A board in the garden...
Can anybody help me to get out of this error, Error programming through Seggar Embedded Studio,
Additional Load File[0] "E:/nRF5_SDK_15.2.0_9412b96/nRF5_SDK_15.2.0_9412b96...