why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
I have PTR9818 module and NRF52840 Development Kit. I flash firmware CLI example(SDK for Thread and Zigbee 2.0.0) for PTR9818 module and communicate with PC use USB-USART...
Hallo,
Currently I'm investigating different Low Energy Bluetooth solutions for our healtcare products that we build in Televic Healthcare.
So here is the setup I...
Hi all,
I'm a little bit confused with the Thingy52 SDK.
The "ble_app_thingy_s132_pca20020" code is the same of the "thingy_v2.1.0.HW_1.0" precompiled hex file?
Thanks...
Hello
I would like to know GPIO leakage current, especially when the GPIO outputs Low
state, leakage current flow thorough the High side MOSFET parastic diode.
If nobody...
Hey everyone,
I have measured input current by different transmit powers:
nRF52840
Equipment: Konstanter ssp 240-40 as current source
Agilent 34401Afor current measurement...
I have a custom board on which I am running the fatfs example from SDK15.2.
On SD Card Initialisation the CMD0 response is unexpected: -
Where the NCR would be expected...
Hello-
We are preparing a product for Bluetooth certification. Our design has a PCB antenna and the the testing house is requiring an SMA RF coaxial cable to interface...
I have created a custom Board Support file for my custom Board But it is not able to advertise the BLE Device after I use My custom Board File. When I use Predefined board...
Hi,
We need to collect sensor data from nrf52832 and after some processing, we plot data and generate some notifications etc. on smartphone app.
Shortly we need to design...
Hello, I'm developing a solution by using MESH SDK : nrf5_SDK_for_Mesh_v2.1.1
There is an ASSERT on access.c in nrf5_SDK_for_Mesh_v2.1.1_src\mesh\access\src\ as below. ...
SoftDevice: S132_5.1.0
Environment: I have 1 Device Advertising and about 200 "tags" waking up every 10 seconds and scanning for those advertisements and connecting, I have...
HCI for NRF52840
Hello
I m using a STM32 + NRF52840 and i have a mbed project in my STM32 and i want to use The NRF52840 only as a Bluetooth component, is there an example...
Hi guys,
I compiled the openbootloader example and when I try to run it on NRF52840, It gives segmentation fault:
(gdb) load nrf52840_xxaa_debug.hex Loading section .sec1...
