I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
Hello, boss, I used twi read/write data from others device, I find a strange problem, When in no-blocking mode, mainly loop use "sd_app_evt_wait" TWI can't write data to others...
Hi, all. I have been going through the mesh examples and have been able to do the light switching, dimming etc examples and have used the RTT as well as physical buttons to...
Hello everyone,
My problem is the next one :
I bought a Nema 17 stepper motor (this one : https://www.pololu.com/product/2267 ) and it’s driver (this one : https://www...
It appears to be an error in the function signature `sd_ble_gatts_hvx()`.
Since the call is made via software interrupt, the const qualifier is cast away regardless.
So...
I am trying to implement the HAL interface for USB devices in Mbed for the nRF52840. Mbed is currently on nRF SDK14.2 so I may not have all the most recent bug fixes for the...
Hi,
I would like to run a different LWM2M client other than leshan LWM2M. Could you please answer me following questions:
i) Can i run any other LWM2M client written in...
Hello,
To improve the performance of SAADC, I would like to isolate the SAADC from the bad effect of DC/DC and RF.
I assume that SAADC has some noise because of DC/DC...
SDK 15.2's scanning module tries to connect to advertising peers that pass filter criteria when the nrf_ble_scan_init_t connect_if_match field is set true even when the advertisement...
Hi Forum!
I have to understand NRF52 chip for my job! I used to work with STM32 before. It has "Interrupt" (e.g when I receive one byte via SPI, It generates one "SPI_Rx_Interrupt...
Hi, all. I would like some serious help. I have three nRF52840 boards and have been running all the examples from the blinky to light switch/dimming. I am, however, stuck...
Hi,
could you please explain me what nrf52840_peripherals library (located in nrfx folder) is actually doing and what do the numbers next to the definitions mean ?
I see...
Hello everybody, As part of the evaluation of the nrf52840, I have made range measurements. In the course of this I was also concerned with the question to what extent the...
hi,
I am compiling nrf52840 light switch sample code in an embedded studio, I am getting the error as extern "C" {: Invalid argument, how to get out of this
I just began working with the NRF52, using the SparkFun breakout board. I'm developing in Segger Embedded Studio. I am aware that there are drivers for this chip in the SDK...