Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
Is there any way to program UICR registers using Keil ULINK programmers?
I know that the algorithm it uses to program Flash does not support UICR. However, I am able to...
Hi,
I tried looking for an answer for this, however unsuccessfully. I have a custom characteristic and I set it with a string of values when it is added to the custom service...
Hi Everyone,
I'm having some trouble understanding the different combinations of low power modes and how to use them.
When I first power up my board I use about 500uA...
Hi team,
We are doing indoor navigation project using BLE nordic beacons and we are using ble_app_beacon as a transmitter.
We are calculating the position of person...
Hi there, i'm trying to connect to the internet from my nrf52 chip.
one way i think, we can use the ios as a shareing point for the embeded world.
And i tried from a win10...
Hello,
I have a Mesh application using the nRF5 Mesh SDK version 2.0.1.
I wish to implement the possibility for a node to forget its provisioning status and become unprovisioned...
Does the NRF51 DK come with a SWD interface connector-cable to plug into a PCB's SWD port when flashing/programming code into a WLCSP chip soldered onto the PCB? If not, are...
I'm trying to setup a simple host node to broadcast a attention message with no definitive destination node. I need any of the child nodes (primarily asleep) to see and process...
Hello everyone,
I tried to use the example project " ble_ant_app_hrm" SDKv14.2 but it doesn't work. The bluetooth connection work correctly, I connect my smartphone with...
Hello Nordic
I am developing our device. It uses SDK 14.2.0 and s332 SoftDevice.
This device communicate our app by using ble as peripherals.
I thought that our project...
Hi,
do the AES CCM module, AES ECB module, and the Cryptocell 310 (in nRF52840) employ measures against side channel attacks? I am mainly concerned with timing analysis...
Hi all,
I'm working with nRF52840 PDK and I'm using the last SDK and SoftDevice version: SDK v15.2.0 and SoftDevice v6.1.
I'm using the scanning module introduced in this...
hi
I am using nRF52832.i have added 3 service and and 3 characterastics to one service
1.Peripheral service (accelormeter + gyroscope sensor) and 3 characterstics
2...
Hi, Nordic team. I'm planning to create an iOS 11 BLE app.
I want to create a BLE app that can approximately depict indoor locations after the iOS device scans BLE beacons...
Hello,
I am thinking of using Thingy52 for my project. Before I order Thingy52, I would like to make sure if it will workout for my project.
(1) I wonder if data collected...
