I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hi, I am using https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo with segger embedded studio and nordic thingy52 modules. I have problem with the mesh assert which...
Hi,
I'm new to this product and I'm facing some problems in dowloading the required softwares to program the nRF52 DK, I saw most of the tutorials here and they are old...
I was trying to upload one of the examples which is ble_app_hrs file to test nRF52 DK. However, it gives me a message that i have about 31 errors.
Below are some types...
Hello Everyone,
I am an experienced engineer but actually a beginner with Bluetooth technology. I am working on a project that uses a Fanstel BT832AF Bluetooth module. This...
Hi,
I need to be able to put larger strings in the scheduler. At the moment the maximum accepted values for init are the following:
#define SCHED_MAX_EVENT_DATA_SIZE...
Hi, I am confused by this config.
static void drv_keyboard_gpio_init(void) { // Make sure that columns will drive 0 when they will be configured as outputs. NRF_GPIO->OUTCLR...
I'm using a NRF52840 with S140 softdevice. I advertise some data and I want to be notified when advertising start. I followed this thread and I use the customs ble_radio_notification...
Dear Nordic Team,
Thanks for supporting.
Still i am work with keil IDE. But now i want to go work with Segger embedded studio because of mesh concept. Please give me step...
I have combined light switch client and ble_app_uart example by following this guide and this case ,but after I added the codes :
#define MESH_SOC_OBSERVER_PRIO //<set...
Hi,
I am developing stuff for a bike and need the Bluetooth Cycling Power Service 0x1818
I found the 0x1816 Cycling Cadence and Speed
Has anybody developed this service...
Hello I'm a beginner and I try to use the DFU. I use the documentation and I can send my init packet without any problem. But when I try to send my Firmware I have 2 problems...
Hi,
Our system is based on the nrf52832 with SDK BLE_2.0.1 for the mesh. I have few queries as per below,
1)It would be great if you could suggest any vendor who is working...
When Going into Sleep, I see peaks of 12mA every 30ms (see image) I'm assuming I can adjust that changing the connection interval settings. I have my Connection intervals...
