I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
We are planing to use N52832 to design a product using BLE secure feature. Our customer want to know whether the key exchaning procedure is using ECDH (P-256 elliptic...
I've looked at how other projects handle sending large amounts of data and they all use a derivative of the TX/RX scheme that is used in the image transfer demo. The Peripheral...
I'm currently working an nRF52 using SDK 14.1 and Softdevice 5.0.0
We're having a problem where the microcontroller is crashing after a few days for seemingly no reason...
Hello,
I am using nordic sdk and working with C files.
But i would like to work on with C++ files as well.
How will i modify the makefile so that it can build both...
Hi,
Giving make flash command uses segger jlink in the interface MCU as programmer right. I tried to use nrfutil dfu serial -pkg package.zip -p COM_PORT for UART transport...
Hello,
I'm preparing production.
My development environments are :
- SDK : V12.3.0, IDE : miniJLink, Softdevice : s130_nrf51_2.0.1_softdevice.hex
- OS : Windows...
Hi Sir
I'd wnat to develop FW of Ublox NINA-B3 module by Mbed-OS, it includes nRF52840 chip.
Could I just enable the target "NRF52840_DK" and just modify the GPIO number...
Hi,
I have been using the nRF55 DK, through the external debug interface (P20), for programming my custom boards since I started working with the nRF52832 chip. So far,...
Hi,
I have a problem with nrf52dk SPI with the mbed compiler. In the mbed pin names file for nrf52dk the pins are p22,p23,p24,p25. I connect many spi sensors and not working...
Hi. Does anyone know where I can download the CDC ACM diver for windows 7?
I am running the example on the nRF52 dev kit, but I get an error as windows can't find the driver...
Hello all,
I'm new to nRF24L01 and trying to get the evaluation kit ( with Nordic's software) to work on windows 10. After reading previous threads, I used windows xp...
Dear Nordic engineer
There are two problems with the impedance matching of the nRF24L01 + .
1.How to test the local oscillator leakage in RX mode?
2.Is the test program...
I am developing a multi-link application where several Peripherals take turns transmitting real-time samples to a Central, generally about a 156 byte payload per transmission...
Hi,
As if we follow the steps given in the link for the update for combining Mesh SDK v2.0.1 and nRF5 SDK v15 posted by Hung Bui, I found out several problems related to...
Hi
I am trying to add the secure DFU bootloader (BLE) code to an existing application for the nRF52840. I'd like to send the logging information over UART. What are the...
