Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi friends I use nrf51822 with sdk12.3 version and I want to use infrared receiver.
What method should I use to write the infrared receiver code?
Also, does nrf51 have...
Hi,
I'm able to send arbitrary information to the host using generic HID descriptor (uses vendor defined page). There is no driver issue. I'm also able to connect to the...
I am currently downloading softdevice (S140) on our custom board using P19 connector on nRF52840 DK. Our custom board also has nRF52840. It seems the dsoftdevice is downloaded...
nRF52832 & nRF52810 don't support the Bluetooth 5 Range Extension (Coded PHY):
https://devzone.nordicsemi.com/f/nordic-q-a/39532/is-it-only-nrf52840-s140-which-support-bt5...
Whenever I deploy an example to the Fanstel BT840F with Segger ES, the S132 SoftDevice is always also deployed to it. I have attempted to change references to this in the...
Hi,
nrfx_uart.c has a bug where, once there is a RX error, the receiver gets stuck in a disabled state forever. This is because p_cb->rx_enabled is never set true, so the...
hi, my name is tyto I just learned programming about nrf52832, before I used to work with Arduino, after trying to learn nrf52832, it turned out to be very difficult for me...
Hi,
I'am using SDK v15.0.0 with the BLE OTA DFU bootloader. Is there a possibility to access the bootloader start address for a static assert in the application at compile...
We have bought nrf52 832 development kit.
When we checking the kit in nrf52 utility than it detects the IC nrf52 840 .
Hence we have erased all the memory in the DK...
Hi everyone,
I am using the following files to configure uart for laser distance sensor.
Serial Library
I am able to write command to the Laser sensor and also the laser...
Hi,
As far as I understand from this page [https://openthread.io/platforms Host / 802.15.4 Controller section] it is possible to have Dongle running thread attached to PC...
Hi, everyone,
We develope project on nRF52832 Chip. It has one UART port and we need to make it working as RS485. For this purpose we connected to TX/RX pins the required...
I am trying to send hundreds bytes to peripheral, the best tool that I can find, is still nrfConnec. But the data only be typed one by one. Is there any way let it load a...
I am using a nrf52832 with SDK 15.2 and softdevice s132 v6.1
My peripharal should transmit an iBeacon to wake up an application on the smartphone and also transmit a connectable...
