Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi,
I am having issues to program a NINA B112 using the debug out port on the PCA10040 development board connected with a tag connect 10 pin cable, but when trying to program...
The project is cobbled together, but starts from TWIsensor in the SDK 14 examples. The project is compiled with the gcc toolchain which has not given me any trouble. The project...
I am trying to use UART with interrupts and fifo, by using nRF52 SDK 12.2.0 example. It works until the first overflow, after which I cannot any more receive characacters...
Hi!
I'm using an NRF52 with app_uart. As expected at 115200 baud rate, I occasionally get overflow errors which I can see in my event handler.
However, after these errors...
Hi,
Where are scan requests sent? I'm trying to find the function that does this because I would like to disable it.
I only want to connect with a peripheral based...
Hi everyone:
I am using the NUS (nordic UART service) in my project, and find one problem in this project. The development bench is: SDK13.0, nRF52 DK.
If I build a NUS...
Hi,
I used IOT TCP Server example of nRF5 SDK(Ver.15.0) to complete the communication
between the Raspberry Pi and the PCA10040.
But I found that the communication speed...
Hi,
1. I want to disable MCU UART connection which is SB with GPIO pin 5, 6, 7, 8 and I need to connect that pin on arm based processor so desoldering those short bridge...
Hello,
we are facing a weird issue with a few models of smartphone since we increased the max MTU size. We are testing at the office with the Xperia E6553 but the Samsung...
Hi there
I am stuck. My incremental wheel with photocell and comparator circuit does not work if the QDEC hangs on it. But seperately it works fine.
When I hang it to...
Hi Team,
Which models are supported in the latest mesh SDK?
I can see support for the on-off model.
Is Time and Scenes (Explained in Mesh Models.pdf, Section-5, Page...
I use SDK13, nRF52, S132
I use bootloader_secure_ble with generated public key for bootloader and for nrfutil. After all steps like discribed on
devzone.nordicsemi.com...
Hello.
I use nRF52832 and power from 3.3V source. Also I use the accelerometer and gyroscope with VDD 2.5V and 3.0V respectively. They are connected to nRF through SPI....
Can a device that is configured and programmed from Keil (softdevice, application, bootloader) be updated with code that has been compiled on ses (application)? I have converted...
