Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hello,
I have followed the instructions for openwrt on rpi2 devzone.nordicsemi.com/.../
and was able to establish connection Bluetooth 6lowpan connection between Rpi and...
HI I am working with nRF52 DK
softdevice s132 sdk v11.1
I tried out the SPI master and slave examples and they work fine (I can transfer and receive data)
I have been...
Hi,
i have an custom board, using s110 and HID example from sdk9.
After i pair and unpaired few times i get an error code :err_code = 0x8010
err_code = dm_service_context_set...
Hey! I was trying to modify s132 ble_beacon example to s140 for my nRF52840 DK but I couldn't build it in Segger Embeded Studio. What is the problem with "SEGGER_RTT_CONFIG...
Hi,
I have an nrf52 with sd 132 3.0.0 and SDK 12.2 which after turning it on I can connect to it without problems, but after some time (maybe 10-15 minutes) I can't connect...
Hi,
I am using sample ble_hrs code in SDK12.0.0 over Rigado eval Kit for BMD300. After running original code as it is device doesn't advertise. After I commented out the...
I have modified the ble_app_uart to start and stop advertise by receiving command from the uart port. If I don't delete the ble_advertising_on_ble_evt(p_ble_evt); in below...
Hi team,
Iam using (\ble_tester\examples\ble_central\ble_app_hrs_c\pca10028) this example.i want to get rssi from the advertising beacon.
Iam using this functions
sd_ble_gap_scan_start...
I see on your website that Bluetooth 5 throughput numbers are given in the graph below. And the following disclaimer is given.
"Net data throughput not including overhead...
I have taken a look the APIs which the S132 supports in nRF52 DK.
However i could not find the APIs that can initiate the channel map update ,feature exchange & version exchange...
hai
i have this code to save and read some data in flash.but the stored and read data are not same. always reads zeros. how can i solve that.........?
here is my code...
I'd like to be able to quickly update the advertising data using
sd_ble_gap_adv_data_set()
and at the moment I'm doing this via a bit of a hack, as I captured the advertising...
Normally, Raw data has TYPE (0x01), TYPE (0x09): device-name, TYPE (0X07): UUID 128 bits.
However, there are devices without TYPE (0x07).
Is this also a problem?
Communication...
