I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hi
Im trying nrf52832 with 0 BMD-350 Evm.
Working with IAR, nRF5_SDK_13.0.0_04a0bfd.
I need ble_app_hrs_pca10040_132_uart working properly.
Seem like there is a main...
On very rare occasions when a connection is made, our device manager (peripherial) callback gets called with event id = 0x23(DM_EVT_DEVICE_CONTEXT_DELETED?) and event result...
Hi,
I am performing "just pairing" using peer manager ( SDK 11.0 ) in my custom board which uses nrf52 chip.
I am getting this events
PM_EVT_CONN_SEC_START,
...
Hi, I'm using nrf8001 nordic chip on my project. With some time on the nrf8001 chip begins to send the HW_ERROR with failure on ll_lm.s0.c and line 571. This not crash the...
Hi,
I am using the nRF52832 and I have been trying to meausre the centre frquency on a specturm analyser. But, the centre freq on the specrum analyser is 1.81GHz when it...
Hi,
I have a beacon that uses 4 AA batteries, each has 1.5V and 2600 mAh. When connecting the board to the PPK I get the attached measurements when doing a lot of scanning...
Hey guys. We are using the NRF52 with SDK 13.0.0.1-alpha.
If we connect the NRF52 to our own android or iOS APP we have some timing problems with notifications. When the...
I would like to reduce current consumption on my beacon and I wonder if it is possible to disable sending scan response. I know that it is not a huge difference in a single...
Firstly，the RedMi Note3 DFU failed used by dual bank，however Xiaomi3 Phone can DFU successfully.As the question link text mentioned,the process of the RedMi Notes3 Phone DFU...
Hello Nordic,
i am trying to interface BME280 with nordic nRF52 and SDK v 12.02 using twi_peripheral but i am unable to do it. here in example they are using ls75b whereas...
How do you setup "immediate Service Alert" Client on iOS, in order to get notified when an action is taken on the bluetooth peripheral ? (eg. Button press)
Hi all, I have an nRF52832 which is woken up every 15 seconds by an RTC to check for ESB broadcasts. The nRF52 will be powered continuously until the battery runs out, so...
I want to use AES ECB block present on nrf51 and nrf52 boards for resolvable private address (RPA) generation.
Are there any measurements about how much battery the...
I have an iot/coap environment setup and i want to read input voltage connected to p0.01.I can read the input in terms of resolution(0-1023).I can convert this values to voltage...
