Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hi,
See attached photo for layout placement of the trace antenna.
Altium PCB File : 108-0013-01 PCBA MAIN.PcbDoc
Background :
This is a design for a wearable...
Hello,
I am using SDK 11.0.0 and attempting to integrate the BNO055 IMU into twi_sensor example and then connecting the IMU data over BLE via ble_app_uart.
I successfully...
Hello,
I have two devices sharing an I2C bus. These devices are the MAX86150 and the MLX90614. DMA is being used. I2C is running at 100 KHz.
After initializing both...
Hello,
I'm currently working with sdk 11 on nRF52832.
I'm trying to acquire 20 value from SAADC every 10ms during 300uS.
I think that the rate is too high because...
Hi , why I can't have an update of my bootloader ? Here is the script I use to generate the .zip file :
nrfutil dfu genpkg --bootloader Bootloader.hex Boot.zip
The...
i have RBL nrf51822 ble and i want to try it with BLE Sniffer. i flashed the nrf sniffer hex file by drag and drop to my dongle but it doesn't show anything. only it shows...
Hi Everyone,
I am working on a hobby project with nRF51822 which needs me sample upto 4 signals reliably at 500Hz each at 10bit resolution. I have read through few posts...
Hi all,
I have two nRF52 connecting, transmitting, disconnecting and sleep mode when are in normal operation, now I am experimenting a randomly error code 8 when calling...
Dear Nordic Team,
Meanwhile, I've burned through a week finding a solution for this problem.
Now I am out of ideas where to check for problems.
My application:
I...
Hi, I use the following.
Raspberry Pi 3 (RPi3 with Raspbian Jessie 4.4) as a router,
RPi3 is connected to a Wi-Fi router to access the Internet by using the built...
I'm trying to flash a nRF518122 with a St-Link V2 programmer via Open OCD.
The process seems to goes smooth, but comparing the number of written bytes to the actual HEX size...
How is BLE_CONN_HANDLE_INVALID changed in multiple services
I modified the ble_sdk_app_proximity example. I added x3 services, based on the BLE Characteristics, a beginner...
Hello
im building a project for discovering infections through temperature sensors, so im modifying the heart monitor sensor examples (central and peripheral) in the sdk...
Hi
I am developing an applicaztion with SDK 13.0.0 and S132 for nrf52832
The version of the softdevice to be used with this SDK is 4.0.2, and I need access to L2CAP layer...
