I was doing development on the development kit and I noticed that when flashing the device there is application core and modem core firmware that is flashed
I'm trying to...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have designed a custom board based on nRF5340. Now I am trying to do flashing and RF testing of it through nRF5340 development board but can't even flash it because...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi,
My first objectif is that the Micro:Bit consumes less than 2μA without the BLE. I read that the Micro:Bit program was not powered if the Micro:Bit is powered by the...
Hi everyone,
I am writing a program in Keil whereby I have to send a large amount of data through BLE notification in real time. The program works by having two timers...
I want nRF52832 to be a central device which will take an input from nRF51822 (peripheral device). Also, Is it possible to make two nRF51822 talk to each other?
Hi,
I having an nrf52832 board and using gnu arm, nrfjprog to program the device. i reading data from two different sensors using spi and TWI in two different codes. now...
Hello all,
I have received "nrf51822 smart beacon kit" connected the battery power and i can detect the device in nrf Beacon app. but the issue is when i select the actions...
I am going to have streaming data come through a characteristic on an S110 device. When the client writes to the characteristic, my peripheral device will read the characteristic...
How do I use Wireshark to see the connection interval negotiated between my nRF51822 peripheral and a central which is a mobile app? Which messages should I be looking for...
Hi all,
I am not very proficient in NORDIC and BLE. I was wondering if you could answer me.
I am developing a module using NRF52. I have a redundant wireless communication...
I am using a PCA10040 with a nRF52832 mounted on it. I am trying to match the IC revision with the packet variant as explained here .
The problem here is that the chip...
Hi I am new to Nordic development and set up all the tools required for compiling and flashing program to nrf52840 0n ubuntu. I downloaded nrfjprog and jlink segger and put...
Hello,
I'm trying to use a nrf51 dongle (PCA10031) as a BLE sniffer. I'm following the ble-sniffer_win_1.2_User Guide.pdf.
On the required software, i need to install...
Hi,
I try to use the example ble_peripheral -> blr_freertos -> ble_app_hrs_freertos and I add to the thread a fds_register() and fds_init(). Problem: In the call back function...
Hello, I am using the NFR52 DK (s132) in peripheral mode. I have implemented a pairing mode based on a static passkey. However, the available time to enter the key in the...
Hi,
is it possible to atomically change both the GAP address and the advertising message in one step? I want to broadcast two different advertising messages with each of...
