Hello,
For our emission tests in an anechoic chamber we need to be sure that the BT antenna is up and running. Of course we cannot connect via BT from outside the chamber...
hi support team,
docs says we can program 54l15 external spi flash ,please refer to : https://docs.nordicsemi.com/bundle/nrfutil/page/nrfutil-device/guides/programming_external_memory...
HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
PLEASE CANCEL THIS TICKET
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi,
I use nRF51422 in Dual mode(SD310) with SDK10 Version.
The profile is CSCS.
I want to ask
How to just show Speed Sensor or Cadence Sensor.
Here is what I did just...
Hello,
I'm evaluating the feasibility of using the nRF52832 chip on a board with a microprocessor running Android and I like to know if Nordic has released or is planning...
I'm using SDK nRF5_SDK_13.0.0_04a0bfd and compiling the example ble_peripheral/ble_app_hrs/pca10056/s140/armgcc using Eclipse Mars 2.
Flashing softdevice s140_nrf52840_5...
Dear Nordic.
I cant found stack API documentation for study.
All company give it for user, for example TI.
User open doc folder and can reed API.pdf file.
Where your...
I use NRF51822_xxaa, sdk12.2, arm_gcc 4.9_2015q3
when i flash hex file experimental_ble_app_blinky_pca10028_s130.hex from C:\NRF\SDK_12.2.0\examples\ble_peripheral\experimental_ble_app_blinky...
Hi,
i have NRF51822 beacon(PCA20006) and NRF51dk KIT(PCA10028).
I am connect a touch sensor and it's gives output in form of "HIGH & LOW".
and i am able to detect the output...
hi,
i want to connect sensor to nrf51822 to send data to smart app continuously over ble.i want to modify example ble_app_beacon. which functions i need to change?
Hi all,
I have implemented a service with various "long char" characteristics. The buffer that I use to receive the data wrote to the "long char" characteristics is this...
I use SDK 9 and nrF51 in the advertising mode. I want to advertise each 1s packets.
First, I call function
set_adv_params(&m_adv_params);
where I
static void set_adv_params...
Hello,
I try to implement the BLE / Cycling Speed and Cadence Service and try to figure out, how to initialize the ble_cscs_init_t data structure. Currently I'm wonder how...
I am building a cadence sensor form the Cycling Speed and Cadence Service module.
Unfortunately the sensor I have built is recognized to have both speed and cadence when...
hi
i flashed s110 softdevice 7.1.0 then ble_app_beacon example application fron sdk 7.1.0 into nrf51822 beacon successfully.but led is not at all blinking in beacon.and i...
Hi
I have got two nRF52840-pdk for long range application design. After reading posts here I realized that the softdevice s140 can only change PHY to CODED after a connection...
Hii guys I am using an nrf51 DK board for my project and I am trying to find the number of advertisements send from the time the board was power up or reset. From my knowledge...
