after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
hi
I develop nrf52832 based ble device, this based rtos therefore ble communication have critical
time limit.
I will use mesh protocol my ble device, in the environment...
GLS is implemented using Nordic(S110_7.0_SDK6.1).
When set to Control solution function.
The setting of the device and the READ value of the application do not match...
I am trying to integrate an iBeacon Library on nRF51-xxAC with SDK10.0.0 and S110v8.0.0 . Can anyone please help me out if any one has ported the iBeacon Library and what...
I want to implement one central device to ten peripheral devices connections.
I'm using nRF52832 DK and S132 5.0 and SDK 14.0.
So, I have run multilink_central example...
I managed to sniff Nordic mesh sdk 0.9.2 packets on raspberry pi 3 using "hcidump --raw", and I can read the raw hex data of mesh packets of light control demo, but since...
Trying to interface this module with atmel core micro.
We are able to transmit data by this module but not receiving the data at other end.
At transmitting side we are getting...
Hi,
Currently I'm working on nRF52 with SDK11 and SoftDevice S132.
Till now I've worked with IAR and my code was based on the "ble_app_uart" and the dfu "bootloader" examples...
WHAT EXACTLY IS THE PURPOSE OF PPI. IF I AM GENERATING A PWM SIGNAL IN PIN NO 21 AND USING A WIRE I CONNECTED TO PIN NO :24(BOTH GPIOS) IN NRF51422 BOARD AND WANT TO COUNT...
Hey I was using the relay example in SDK 12.2 on the s132 NRF52DK.
We added a service and characteristic using the Nordic tutorial - devzone.nordicsemi.com/.../
Using...
I have a very simple test script which enables a BLE service (only the Generic Access and Attribute), advertises and waits for connection. It also sets four pins to input...
We made a READ request from the client with nRF 52 as BLE peripheral.
READ was automatically repeated 10 times when writing 200 bytes of data in a characteristic fashion...
I want to program my nrf51822 aa module but when any softdevice has been already programmed, it doesn;t work..
it says error of erase failed..
flash download failed cortex...
Hello,
I am using nRF52832 DK s132 and interface with accelerometer. Now i have successfully read 3 ADC channels with time period of 244 microSecond on terminal. But i have...
Hello,
I am working on an nRF52832 application that uses SoftDevice S132 v3.0.0 as BLE central, BLE observer, and a proprietary protocol using the timeslot API.
Sometimes...
