Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi. I'm using nrf52832.
Now I'm using HFXO, LFXO to operate BLE. As I know I should use HFXO to operate BLE.
What about LFXO? Can I use internal clock(LFRC RC osc) instead...
Hi,
I am working on the latest version of SDK (v14) and SoftDevice(v5) on nRF52382. When I call the sd_gap_disconnect it returns NRF_SUCCESS. However the BLE_GAP_DISCONNECT...
I was trying to verify the DFU functionality on SDK 14 on nRF52832. Here is what I did.
1. Using nRFgo to erase all
2. Program bootloader/soft device with C:\svn\nordic...
Hi,
I am using SDK v12.2 and gcc compiler. S132 softdevice for nrf51822 controller.
And i am using s132 softdevice.
I want to connect multiple nrf51 devices (approx. 14...
Hello sir,
I am using nRF52832 board and interface with 3 axis accelerator reading ADC for 3 Channel. I have use sample code for controlling in timer/RTC mode. My ADC is...
Hi,
I'm doing some measurement on the radio peripheral of the nRF52840 using the generated events and a timer which is set to run at 16MHz. Radio events and Start/Capture...
SDK version: 13.1
Hardware: nRF52832
Eclipse version: link text (I could not get the marketplace working in the latest Mars Eclipse version, so I downloaded this version...
I am evaluating the sdk14 ble_app_uart example. I am able to run this code and connect to this uart service but do not see messages get passed to the uart pin. Only when I...
I am using a nrf52832 Development Board with s132 for some BLE applications. I developed a beacon app, set for BLE peripheral, and every reading of the advertising from this...
Hi,
I'm using NRF51 DK board and i am following characteristic tutorial available. I am able to send temperature value over Bluetooth by using light blue app.. Instead of...
I am using nRF connect to debug an application on a nRF52832. When I perform a scan, I can see the UUID of the nRF52832 device I want to connect to. Where is this UUID stored...
Hi,
I'm unable to auto connect with nrf51 using nrf Connect App, if I select Connect using Auto-connect only and no Bonding in nrf Connect App for first time.
With Auto...
Hello,
i have a question about the range. I have a Bluetooth-Module with nRF52832. I tested it in my Office. Additional I can Change the Output power from +4 dBm to 0 dBm...
My use case involves buttonless beacons that should only be connected to by authenticated users on their mobile device (Android / iOS).
Once connected, these beacons will...
