Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi experts
I am trying to interface an external ADC to NRF51-DK i am presently reading SPI ADC code values on BUTTON press event. I am able to read the values from ADC...
Post in reference to link
After flashing light control server or client app on PCA10028 app crashes with HARD FAULT.
Steps how I built the app:
Using freshly downloaded...
Hello,
I find that some examples such as ble_app_uart uses a GATT_MAX_MTU_SIZE of 158, and it has initialization in function ble_stack_init().
// Configure the maximum...
Hi. I'm using nRF52832. I need more GPIOs and UARTs. So I think nRF52840 is very good solution to me.
But as I know, nRF52840 is just engineering sample now.
When can...
I am running the Iot SDK Cloud MQTT example on a nrf52 DK. Is there are reason why MQTT will only let me subscribe to a maximum of 9 topics. Anymore and some of the topics...
I'd like to get the current connection state eg:
result = get_connection_state()
if(result == BLE_GAP_EVT_CONNECTED)
doSomthing();
Is there such a function available...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
I am working off the ble_cts_c example, using SDK 14.0.0, SoftDevice S140, and nRF52840.
All works well when I pair a device for the first time: the nRF discovers services...
nRF51822 how to save user data to UICR FLASH?
I have some user data bytes wan to save to UICR ,I see the CUSTOMER[0]~[31] is can be used.
how to save it ? think.
like...
The product that is in development could be used by the 100s at the same venue, if we let customers picks their device from a list there will be a lot of wrong connections...
Hi!
I'm having a little trouble with my measurements. A little situation sketch:
I'm using two nRF51822 DK's who act as peripheral and connect to a nRF51 Dongle that...
I'm trying to reduce the RAM requirements of the softdevice for my application and am looking at some of the options in ble_cfg_t.
What does ble_cfg.gap_cfg.role_count_cfg...
According to the NRF52810 datasheet ,The RADIO contains a 2.4 GHz radio receiver and a 2.4 GHz radio transmitter that is compatible withNordic's proprietary 1 Mbps and 2 Mbps...
I am trying to receive ble notifications from a custom UUID as a central device and then relay that information to my computer via ble. I have been following the nordic relay...
Hi
I'm migrating to SDK 14 and have my service's on_ble_evt() function registered. However, p_ble_evt->header.evt_id == 65535 (0xFFFF) for every evt, so I think I'm doing...
