Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
For my project I need to measure the battery voltage while transmitting data to get a good indication of the battery capacity. I've found an old example ( link text...
Hi,
nRF24L01 seems like a perfect choice for home automation project that I have in mind .. I will have to install about 20 of those around the house.
My question is...
Hello,
I'm working on the bootloader using SDK13.1. In the file dfu_req_handling.c there is a variable called m_flash_operations_pending that gets incremented with every...
HI,
I am very new to this, I am looking to put a video or flash player or another image to to load into my nRF51822 beacon kit. I am thinking the straightaway method would...
Hi,
I am working with ble_app_uart code, in that I am trying to configure different baud rates like 9600,38400 and 57600. With these baud rates I am not getting any issues...
Hi
sd_ble_gattc_primary_services_discover() is being called from ble_db_discovery_start() within ble_db_discovery.c. I'm trying to get the ble_cts_c service working. It...
Hi
I am receiving INVALID_STATE (error code 8) from ble_db_discovery_start. According to documentation, this error can be returned "If this function is called without calling...
Hi, i have just bought a NRF51 DK. I have tried to run the precompiled Blinky example. I have first installed NRFGo Studio. I connected the board. In NRFGo Studio, I selected...
Hello,
I am making a battery service to report the battery that is sampled by the SAADC, so far I am am able to compile it and debug it, however I see how my saadc_event_handler_interrupt...
Hi
I'm reading the debug output of ble_cts_c.c:
NRF_LOG_DEBUG("BLE event handler called with event 0x%x\r\n", p_ble_evt->header.evt_id);
However I can't find any...
The analog circuits 51822 and rfx2411n supplied by the authorities are connected 52832, but the circuit is not working properly.PA and LNA switching has been controlled in...
This is to build upon a previous question i had here .
This time, I am having issues with SDK 14.
I can compile and run the BLE peripheral HRS example fine. With SDK 14...
Hi,
I am trying to write 64 bytes to a characteristic as a client and am getting the error NRF_ERROR_DATA_SIZE . The infocenter is not very helpful at indicating where...
I am using S132V3 on NRF52832 device. In my application we need to set a static, non-rotating, private resolvable address. I can't get into why that is here. In theory this...
Hi all,
I'm using chip nrf52832 with the last enabled stack which integrates the adaptive upgrade for bluetooth 5.0. However I'm insterested in long range and that's upgrade...
