I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
I am using sdk12.2.2 and pca10040. I want to add uart drivers in ble_app_template code so that I can use printf to get my data on terminal. Unfortunately I am not...
I AM USING SDK 12.2 AND IT IS RECOMMENDED TO USE FSTORAGE. But i found no function to read unlike pstorage_load . so can i use pstorage instead of fstorage will it cause any...
Dear Helpers,
We are facing an issue. It is all related to DFU (secure buttonless) and Android 7.0 (deployed on a Samsung A5).
We have a code that is running perfectly...
Hi
By playing around with the serializer code for the S132 5.0.0 I found a bug in the serializer/deserializer code.
The ble_gap_evt_auth_status_t has a new field "lesc...
I'm using FreeRTOS in my project and I wanted to check if the APP UART FIFO implementation is thread safe, IE I want to have a reader and writer thread. Each FIFO has a separate...
I want to enable BLE's NUS Service(in Old SDK, nRF5_SDK) with in nrf5_SDK_for_Mesh.
Is it possible?
I'm failing, as starting of this, to use Softdevice for parallel use...
I HAD ASKED THIS QUESTION: we have used the NRF51822-BEACON KIT EVAL BLUETOOTH SMART BEACON which includes RGB LED, but cannot find a non dev kit model with RGB LEDs . can...
Hello sir,
I have develop project and their lots of quantity. I want flash my updated program into my nordic device without open this device via BLE services. Is it possible...
Found on the web:
"Properly configured WiFi network shouldn’t interfere with the Bluetooth signal. The best practice for WiFi configuration is enabling WiFi on one of the...
Hi
I have a project use nrf52 to have a purpose below.
Maybe after some pairing process with smartphone.
The user can trigger the device(nrf52, may press a button...
Hi guys,
I am trying to connect my BLE Nano 2 with HM-10(as a Peripheral device) using Arduino Central_test program.But the problem is it is not pairing with it,but detecting...
Hello,
We try to use "ATT_MTU" and "Data length extension (DLE)" to expand a packet in S132 SDK 14.0.0.
When we set "ATT_MTU" > "DLE", please tell me what happens?
...
i am in very strange problem and was unable to debug it
i am using following code to write 16 bytes data to flash memory, my app hangs after executing custom_flash_write...
Hi all,
i'm trying to use the function of power warning with s132 and nrf52 with sdk 11.
i use the function
err_code = sd_power_pof_threshold_set( NRF_POWER_THRESHOLD_V27...
