I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
I want to know OBD-II Application scenario
ignore how to get OBD-II information from the car. assume I already get the info
generally, how often fetch the information...
Hello engineers, Recently I test the ADC function,I think the library function is so difficulty for me. So I want to use the ADC by register,but I found that ,after I start...
I am developing on a nrf52 board with a fdc2214 chip. I created 1 custom Service and 3 characteristics shown below, and the format of my UUID is 0000xxxx-1212-efde-1523-785fef13d123...
Hello, I successfully ported one provisioner and one provisionee to 2 nrf52840 experiment boards respectively, now I'm having the provisionee connected to my computer and...
Hi, I asked a relevant questions before and was advised to solicit such information from my local Nordic operations. But they didn't appear to know that either, so I'm here...
Calling ble_nus_string_send() from within a TWI callback (case NRF_DRV_TWI_EVT_DONE) is performing a reset on my PCA10028 (nRF51422). It works fine from the main loop.
...
When I run nrfutil, the program immediately throws a Python exception. It has been working for the last 6 months. I've used pip to try to upgrade protobuf and nrfutil, but...
I AM HAVING A COUNT VALUE WHICH IS IN THE RANGE OF 10000 - 100000 WHICH IS TO BE TRANSMITTED OVER THE BLE (OF THE BOARD) TO THE ANDROID DEVICE. I like to use nus service to...
Not really a development question. I'm looking for a wearable BLE device to use as a prototype for an academic research project (in a healthcare/hospital setting).
The...
Hi there,
Can anyone help me do secure DFU using bluetooth on PC please? I've tried every possible node.js solution to no avail.
I don't care what programming language...
Hello,
To my understanding, normally, either after a reset or powering up, the program should first run to Reset_Handler, then SystemInit, then __main.
Somehow, my program...
i used RTS service example in nRF5_SDK_13.1.0_7ca7556.
I entered the value in cccd,then i see ATT_ErrorRsp: status=0 oc=0x0012 h=17 err=5.
What's wrong with it and how...
We have tried working with nrF UART android source code from Github, it is not working, we have connectivity issue. it is working fine with the uart application which we have...
Hello, I'm developing firmware for a custom PCB with an nRF52832 chip. I've implemented almost all of the peripheral functionality I need (including TWI, GPIO, GPIOTE, delay...
Hi there,
I've already downloaded ble_mesh_v0.9.1-Alpha SDK and I can use arm-none-eabi-gcc to compile it, one thing I want to know is that how can I switch HWID to 52 in...