Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi all,
It is a common convention to configure the I2C SCL signal to be push-pull instead of open-collector if there are no other I2C masters in the system (saves a pull...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
Hello,
I have a custom nrf5340 board with an attached external RAM on the QSPI (I understand only NOR flash ICs are supported) on the older version of the SDK such as...
Hello Nordic Team,
Currently, we are performing power consumption testing using the Nordic nRF54L15-DK development kit.
As part of this, I aim to fully disable the Radio...
Good afternoon we are updating some Nordic chips but to make the connection work it is necessary to install the modem version 1.3.1 wait for it to connect and then install...
I have a custom board using a nRF52840.
A part of the configuration is a Analog Devices MAX98357AEWL+T Class D amplifier which is driven by i2s0.
When the board is idle...
Hey, I noticed that most of the wearable ble devices (without keyboard and screen) on the market are using 'push to confirm connection' authentication, when you have to push...
Chip nrf51822
S110 nrf51_sdk_v6_1_0_b2ec2e6
Softdevice s110_nrf51822_7.0.0_softdevice.hex
I use "nrf51_sdk_v6_1_0_b2ec2e6\nrf51822\Board\pub\device_firmware_updates...
Hi,
I am trying to set up a custom service and I have it all setup and it works properly. The only problem is that it is advertising as a 16bit service. I am moving from...
Take into account an application on the nRF51822 and S110.
I have defined different custom services, so UUID is 128bit long.
When advertising:
Is it advisable to include...
What are the mechanics of using 'uuids_more_available'? Is this list transmitted as a part of advertising data, scan response data, or both? How does the host know that this...
I'm using mbed+nRF51822+BLE_API+softdevice 7.1.0 for BLE peripheral side. I add uart service with the setting BLE_GAP_CONN_SEC_MODE_SET_OPEN which is open link, and set the...
Hello,
I know that this question was here before, but I've read all of the questions and answers and still I don't know what I do wrong.
I'm using 3 PWM channels to...
Hi
While browsing the new files in the SDK 8.0.0 i had a look in the new ble_advertising module. In the start advertising function the pstorage access is checked if it's...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I have the nRF8001 plugged into the shield for the Arduino Uno.
From the Arduino SDK from Nordic, I have downloaded the BLE Hello World program to the Arduino, which should...
I know the SDK lists it for the S110 stack:
http://developer.nordicsemi.com/nRF51_SDK/doc/7.2.0/s110/html/a00066.html#app_dfu_intro_sec
But trying to use it with the...
There is a GitHub example:
https://github.com/NordicSemiconductor/nrf51-dfu-ble-S130
It states that the SDK 6.1 is required. Will it work with the 7.2 SDK using the...
I am trying to use TIMER1, but it seems that my ISR isn't being linked in during the build.
uint32_t timer1_init(void)
{
...
NVIC_SetPriority(TIMER1_IRQn, APP_IRQ_PRIORITY_LOW...
