Background - We are laying out a new board, upgrading to the nRF54, and wanted to use p2.02 and p2.03 as serial UART lines because p1.04 and p1.05 were planned to be used...
Hello,
I face a problem which I can't understand really and where I need support.
It is strange...
In our electronics we use the nRF52840 which is enclosed in a module...
Hi there,
I have recently upgraded my software to latest ncs 3.2.0. I have noticed that my initialisation does complete but it ends up with fatal error that seems to be...
Dear Nordic,
I am debugging a custom hardware with a nRF7002 on-board, using wifi shell app. At this moment the shell does not work as expected, needs to locate where the...
I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
Do anyone ever measured current consumption of ble_app_uart?
What is current when connected and uart idle, transmitting, receiving, and transmitting while receiving?
Please...
I tried changing the define below from 1 to 2, so I could have one handler for a button and a different handler for other sensors. But my problem is:
If I set it to...
Hello,
I've developed a circuit with Mikroelektronika's nRF T click module. This module uses nRF24L01P but as I see I cannot order it because it is obsolete.
Should...
We plan on use the ST BAL-NRF01D3 balun for a PCB with both an nRF51822 and a nRF51922 on the same PCB separated by about 4 inches.
Should we use the PCB antenna as on...
Hello.
I am very confused with memory layout of nrf51822 BLE examples using SoftDevice stack.
Some examples set IROM1 range from 0x0 to 0x3ffff. (ex, ble_app_advertiseing...
Hi,
I have a nRF51422-EK board (Rev. 1.0) that is bricked.
When connected the LD3 is on.
Jumpers are present on P8 and debugger.
Device manager (win7) assigns...
Hello,
I was puzzled by RM.
I notice POWER control register in peripheral(UART,SPI,TWI) module.
Please answer following questions about the relation between system...
I download the softdevice for PCA10001. And I want download another program, but it didn,t work. The problem I have attached here. As you known, I have push the button 'recover...
We plan on using the external 16 MHz and 32 KHz oscillator inputs to reduce BOM costs since our host micro uses a 16 MHz and 32kHz crystal and it can generate outputs. If...
Hi guy:
I have buy nrf51822 dk .Why I can not download nRF UART App for Android 4.3 at below page www.nordicsemi.com/.../nRF-UART-2.0-for-Android-4.3
Thx
I made code like to below for using 16Mhz system clock.
/* Start 16 MHz crystal oscillator */
NRF_CLOCK->EVENTS_HFCLKSTARTED = 0; NRF_CLOCK->TASKS_HFCLKSTART = 1;
...
Hi guys,
I have designed a custom board with nrf51822. Data transfer seems OK, when I do it through Master Control Panel - I can write data to characteristics and I can...
Hello
I'm planning to use the nRF8001 SCC with an external microcontroller. So far we have purchased the nRF8001 sdk and the nRF6700 Started kid. My question is simple...
