Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Occasionally, when trying to program a softdevice in nrfgo studio, it can't find the softdevice hex file. It was there during the last several programming sessions, but now...
I would like to achieve in the room inside a number of devices to achieve one-to-one binding 8K / S unidirectional transmission of data, is not the use of proprietary_rf inside...
Hi,
I have set up a two NRF51DKs one in a central and one in a peripheral role. Using MCP and nRFConnect I have confirmed that I can send read requests to my peripheral...
Hi,
the documentation page of Gazell warns that it is outdated.
Warning: This is old documentation, and should only be used for historic reference. Please go here...
Hello,
can you help me with choosing the right software components for nRF51 and nRF52 ?
nRF51 on the left hand side works on the battery and turns on when the button...
hi,
I am working on nrf52 sdk11 and s132,
when I am using ble_app_uart example on my custom board I used nrf_delay_ms(10000) i.e 10 seconds when i observe current consumption...
When i use sd_ble_gatts_hvx() send package,i can use the usb dongle get the data package,as it show i can get the information such as, LLID, MESN, SN,MD,PDU-Length show in...
Hello,
I am trying to scan a local name for beacon device on nrf51822 SDK12.0.0 ble_app_multilink_central. The original peripheral sample was working as well. But the beacon...
I am using SDK 12.0.0 and Nrf51 ship.I was trying to compile micro-ecc library in eclipse using make file.I have cloned the micro ecc library from this link .I am using the...
Hi,
I want to eraze the flash page of nrf52832.
Since the default flash page size is 4096 bytes, it takes 90ms to eraze the page.
I want to shorten the time for erazing...
Hi!
I have to do an application is talk via bluetooth. I think i use codec IC to sample the voice then send data via bluetooth. In the receiver device , I use other codec...
I am attempting to write to multiple CCCD handles in a service as a central with no luck. I need to write to one CCCD handle to enable notifications and another handle (BLE_UUID_UPDATE_CHARACTERISTIC...
I am planning to start a project using nRF52832 but do not want to buy IAR or Keil as they are expensive, if I use GCC Compiler with SDK then is it possible to debug the code...
Hi, beginner here..
Frequency hopping used for advertising bluetooth beacons uses which 3 frequencies? Is it possible to choose those frequencies using the software...
