Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi there!
I'm looking to layout a chip antenna using the nRF52832 WLCSP chip and am confused about the layout of the antenna matching circuit. The reference design (CIAA...
Hello,
I am using nrf52 with sdk 12.2.0. I am working with example buttonless dfu template aplication by referring to the link infocenter.nordicsemi.com/index.jsp .
I have...
Hello,
I am running a simple application where I would like to listen for BLE packets for 100ms and then transmit a packet. (no soft device) I can successfully capture...
In section 17.1.9 of the nRF51 reference manual it states:
Maximum consecutive transmission time
is defined as the longest time the
RADIO can be active transmitting...
I need to connect VL53Xl to NRF51 DK> I am using latest 12.2 SDK with Keil MDK.I cannot find any I2C(TWI) example. I can find examples for NRF52 based devices. but not for...
I am using a nRF52832 which act as an observer role only and what is observe it send observed data to another device over UART.
When i turn off scanning and just run UART...
Hi,
I generally use " make flash" (armgcc makefile). If there are multiple devices connected I get a pop-up to select a device/emulator to be flashed. This pop-up just defeats...
Hi there,
I'm trying to use nrfutil generate package with an extern key pair generated with openSSL.
I used opneSLL with prime256v1 curve, which correspond to secp256r1...
Hi,
I use nrf51822 with HF XTAL Frequency of 32 MHz
I am migrating from SDK9 S110 to SDK 12.2 S130 and have a problem that the code stop on nrf_delay_us.
#ifndef...
we wrote a small application to jump to a desired address of our application from bootloader , but UART does not seem to work(i cannot see any transmitted values on terminal...
Hi,
I would like to use the ble_app_hrs to send pressure values via the heart_rate_measurement_send function.
Unfortunately, they are too long: around 105000 Pa (equals...
Hi everyone!
I have an application based on experimental_ble_app_eddystone for nRF52 (SDK12.2), which uses FDS to save in flash memory. Now I want to add the secure_bootloader...
Hello on git hub you add pc-ble-driver
but there is only help how to install it. I did not find any example. And I did not find any documentation how to use it or what is...
Preface: I am developing a software working with different radio protocols (enhanced shockburst, bluetooth,...). Therefore I implemented uart commands for switching radio...
